Z3 Technology Z3-DME-03 User Instructions Download Page 13 | Manualshive

Page: 13 / 54

background image

DOC-USR-0061-03

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

13

Click on “Open Device.” An Internet browser window is opened (default browser used is Firefox)

and the Web GUI appears at the System Setup tab:

Click on the “CH1” tab.

6.4

Configure CH1 and Encode

At the CH1 tab, change Video Resolution to “1920x1080”, set “Output Format” to UDP and “Dest
Address” to the IP address of your PC (in this example, 192.168.0.6). Also make note of the value
of “Dest Port” (should be 5004 by default).

Figure 9 Z3-DME-03 Web GUI (System Setup Page)

«
...
11
12
13
14
15
...
»

Summary of Contents for Z3-DME-03























































Reviews:

No comments

Related manuals for Z3-DME-03

BeoSound Century

Brand: Bang & Olufsen Pages: 29

Brand: ICP DAS USA Pages: 85

Brand: ICP DAS USA Pages: 6

Brand: ICP DAS USA Pages: 107

Brand: ICP DAS USA Pages: 8

Brand: ICP DAS USA Pages: 12

Brand: Velux Pages: 10

Brand: Generac Power Systems Pages: 32

Brand: Korenix Pages: 2

Brand: LevelOne Pages: 9

Brand: AV Link Pages: 2

Brand: Metra Electronics Pages: 9

Brand: Sumitomo Drive Technologies Pages: 30

Brand: Transition Networks Pages: 16

Brand: Digitus Pages: 4

12-110-1250-Bxy

Brand: Eaton Pages: 31

Brand: Diodes Pages: 5

Brand: tams elektronik Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands