Z3 Technology Z3-DME-03 User Instructions Download Page 2 | Manualshive

Page: 2 / 54

background image

REVISION HISTORY

Version

Date

Change Note

Author

2.01.55

11/18/14

Original Document

RC

2.02

03/25/15

Added description of DNS support, “max PTS-PCR”, “Audio Format”,
“Jumbo PES”, “PMT ID”, “Frame Align” and “TS Lowlat” parameters.
Added description of “Refresh” and “Auto Refresh” in status tab.
Added note on VLC decode latency.    Added note on how interlaced
content treated in frame rate divider. Minor updates in Section 2.0,
4.0, 6.0, 6.3, 6.4, 6.6, 9.5.  Updated screenshots and filenames.

RC

2.16

06/10/15

Modified description of RTSP URL in Section 6.6.  Took out “RTP only”
restriction for dynamic changes in Section 6.7.  Changed value to
disable B-frames from “1” to “0” in Section 6.9.  Simplified
configuration procedure in Sections 6.11, 7.4 and 7.5.  Added AAC-HE
and audio bitrate information in Section 9.5.  Added notes that Frame
Sync, and import/export configuration are not supported in this
release. Various formatting tweaks and corrections.  Updated
screenshots.

RC

«
1
2
3
4
...
»

Summary of Contents for Z3-DME-03























































Reviews:

No comments

Related manuals for Z3-DME-03

Brand: Makita Pages: 20

Brand: Daewoo Pages: 36

Brand: Vdwall Pages: 12

Brand: Vdwall Pages: 5

Brand: Promax Pages: 14

Brand: Mutec Pages: 22

Brand: E-matic Pages: 22

Brand: Lika Pages: 2

Brand: M-Audio Pages: 2

CSI-75K-T40001-E

Brand: CanadianSolar Pages: 19

Brand: Cobalt Digital Inc Pages: 62

Brand: EZIHEAT Pages: 34

EA-MEC-PB 150-12B

Brand: EA Pages: 4

Brand: ADF Web Pages: 32

Brand: Urrea Pages: 12

Brand: Martin Audio Pages: 51

Brand: SG GROUP Pages: 112

Brand: Black Box Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands