Z3 Technology Z3-DME-02 User Instructions Download Page 1

Page: 1 / 44

User Instructions

H.264 HD Multimedia System

Z3-DME-02 Digital Media Encoder & Streamer

Model Name:

Z3-DME-02

DOC-USR-0054-02

Manual Version 2.01.20b

Software Version 2.01.20

October 13, 2014

Before attempting to connect or operate this product, please read these instructions carefully and save the manual

for future use.

This document contains proprietary and confidential information of Z3 Technology, LLC ("Z3"). This document may

not be used, reproduced, disclosed, or disseminated to anyone without the prior written approval of an authorized

representative of Z3.

Z3 Technology, LLC incorporates HDMI® technology.

The terms of HDMI and HDMI High-Definition Multimedia Interface, and

the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Summary of Contents for Z3-DME-02













































Search results

Summary of Contents for Z3-DME-02

Reviews:

Related manuals for Z3-DME-02

Brands by name

Popular brands

Z3 Technology Z3-DME-02, User Instructions

Search results

Summary of Contents for Z3-DME-02

Reviews:

Related manuals for Z3-DME-02

Brands by name

Popular brands