manualshive.com logo in svg

Z3 Technology Q603-RPS, Hardware Manual

Share
Download
Z3 Technology Q603-RPS Hardware Manual Download Page 15

 
 

 CONFIDENTIAL                            

 

DOC-USR-0259-02

 

 
 

15

 

______________________________________________________________________________________

 

Z3 Technology, LLC 

♦ 

100 N 8

th

 ST, STE 250 

♦

 Lincoln, NE 68508-1369 USA 

♦

 +1.402.323.0702

 

 

 

3.0

 

30-0104

 

 

The 30-0104 board has the following connections:

 

 

 

Figure 8 Top side of 30-0104

 

 

3.1

 

RS485 and RS232 Serial Port Header

 

 

The J4 header contains a RS485 port and a RS232 port.

 

The RS485 port is mapped to the UART at QUP13 of the Qualcom processor, with QUP13_RFR serving as the 
direction control. The RS232 is mapped to the UART at QUP15.

 

Additionally, J4 provides a 3.3V power source with up to 100mA available.

 

 

The pin assignments of J4 are composite shown in the table below.

 

 

Pin 

Signal 

1 

Ground 

2 

RS232 RXD 

3 

RS232 TXD 

4 

RS485 B 

5 

RS485 A 

6 

+3.3V, 100mA max 

 

Table 6 J4 Pin Assignments

 

Summary of Contents for Q603-RPS




















Reviews:

No comments

Brands by name

Popular brands

Load more brands