Z3 Technology FV4K-DCK-1x Hardware Specification Download Page 1

Page: 1 / 42

Hardware Specification

4K H.265 & H.264 Video Encoder System

Model Names:

HE4K-DCK-1x and FV4K-DCK-1x

DOC-USR-0100-09

Manual Version 1.01.03

February 3, 2021

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

Sony is a trademark of Sony Corporation.

This document contains proprietary information of Z3 Technology, LLC ("Z3"). This document may not be used, reproduced, disclosed, or

disseminated to anyone without the prior written approval of an authorized representative of Z3. Z3 reserves the right to change this product at

any time and without notice. All product names, trademarks, trade names, service marks, or service names mentioned in this document are the

property of their respective owners.

Z3 Technology, LLC incorporates HDMI® technology.

The terms of HDMI and HDMI High-Definition Multimedia Interface, and

the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Summary of Contents for FV4K-DCK-1x











































Search results

Summary of Contents for FV4K-DCK-1x

Reviews:

Related manuals for FV4K-DCK-1x

Brands by name

Popular brands

Z3 Technology FV4K-DCK-1x, Hardware Specification

Search results

Summary of Contents for FV4K-DCK-1x

Reviews:

Related manuals for FV4K-DCK-1x

Brands by name

Popular brands