Z-Com ZAC-1023-5 User Manual Download Page 40 | Manualshive

Page: 40 / 66

background image

40

802.11n mode, wireless client can be divided into HT STA and Non-HT STA, among which the one

with HT protect enabled gets higher throughput.

Enable MAC Clone

Available only under wireless client mode, it hides the MAC address of the AP while displays the

one of the device connected to the Access Point. Default is

Auto MAC Clone

. User may

choose to enter the MAC address to be cloned manually.

Site Survey

Under wireless client mode, the IEEE 802.11n Wireless Customer Premises Equipment is able to

perform site survey, through which, information on the available Access Points will be detected.

Open “

Basic Settings

” in “

Wireless

”, by clicking the “

Site Survey

” button beside “

Wireless Mode

”

option, the wireless site survey window will pop up with a list of available AP in the vicinity. Select the

AP you would like to connect and click

“

Selected

” to establish connection.

Figure 14 Site Survey

«
...
38
39
40
41
42
...
»

Summary of Contents for ZAC-1023-5



































































Reviews:

No comments

Related manuals for ZAC-1023-5

Brand: Tenda Pages: 34

Brand: TRENDnet Pages: 2

Brand: LINOVISION Pages: 17

Brand: H3C Pages: 34

WAP-1000 WireFree

Brand: Planet Pages: 28

Brand: Last Mile Gear Pages: 19

Brand: Linksys Pages: 155

Brand: DeWalt Pages: 8

ARS-7235-PSE-AC Series

Brand: ANTAIRA Pages: 24

Brand: Dynalink Pages: 2

Brand: Yunlink Pages: 33

Brand: Nimbus Water Systems Pages: 10

Brand: VTel Wireless Pages: 2

Brand: Westermo Pages: 21

Brand: ezWave Pages: 64

Brand: Quantum Pages: 18

UniFi UAP-AC-IW

Brand: Ubiquiti Pages: 24

powerbeam m5 PBE-M5-400-ISO

Brand: Ubiquiti Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands