manualshive.com logo in svg

Z-Com ZAC-1023-5, User Manual

Share
Download
Z-Com ZAC-1023-5 User Manual Download Page 6

 

 

Table of Content 

Chapter 1 Introduction ....................................................................................................................... 12

 

Introduction ..................................................................................................................................... 12

 

Appearance ..................................................................................................................................... 12

 

Key Features ................................................................................................................................... 13

 

Typical Application ......................................................................................................................... 14

 

Chapter 2 Hardware Installation ....................................................................................................... 15

 

Preparation before Installation ...................................................................................................... 15

 

Professional Installation Required ................................................................................................ 15

 

Safety Precautions ........................................................................................................................ 15

 

Installation Precautions ................................................................................................................. 16

 

Product Package ........................................................................................................................... 16

 

Hardware Installation ..................................................................................................................... 18

 

Connect up .................................................................................................................................... 18

 

Using the Grounding Wire ............................................................................................................ 19

 

Install External Antennas .............................................................................................................. 19

 

Mount the AP on a Pole ................................................................................................................ 22

 

Power Up ...................................................................................................................................... 23

 

Connect to the Access Point ......................................................................................................... 24

 

Chapter 3 Basic Settings ................................................................................................................... 27

 

Factory Default Settings ................................................................................................................ 27

 

System Requirements .................................................................................................................... 28

 

How to Login the Web-based Interface ........................................................................................ 28

 

Basic System Settings ................................................................................................................... 30

 

Network Settings ............................................................................................................................ 30

 

Time Settings .................................................................................................................................. 33

 

RADIUS Settings ............................................................................................................................. 34

 

Firewall Filtering ............................................................................................................................. 35

 

Summary of Contents for ZAC-1023-5



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands