YSI ProDIGITAL User Manual Download Page 68 | Manualshive

Page: 68 / 78

background image

68

Accessories

YSI Item #

Description

626946

Large, hard-sided carrying case (Fits ProDSS 4-port cables 10, 20, and 30 meters in length, cable
management kit, handheld, and accessories)

603075

Large, soft-sided carrying case

626945

Small, hard-sided carrying case (Fits ProDSS 4-port cables 1 and 4 meters in length, handheld, flow
cell, and accessories)

599080

Flow cell for ProDSS 4-port cables

603076

Flow cell for ODO/CT cables (requires single port adapter; 603078)

603078

Adapter required for ODO/CT flow cell (603076)

603056

Flow cell mounting spike

063507

Tripod (screws into back of meter)

063517

Ultra clamp (screws into back of meter)

603070

Shoulder strap

603069

Belt clip (screws into back of meter)

626942

USB car charger

626943

Small external Li-Ion rechargeable battery pack (Typical performance: will charge a completely
discharged handheld battery to about 50%)

626944

Large external Li-Ion rechargeable battery pack (Typical performance: will charge a completely
discharged battery to full charge, plus have power to charge a second battery to 20%)

626940

AC charger (USA). Includes power supply and USB cable (included with handheld)

626941

AC charger (international). Includes power supply, USB cable and outlet adapters (included with
handheld)

626846

Replacement Lithium-ion battery pack

626969

USB flash drive (included with handheld)

626991

Cable for charging and PC connection (included as part of 626940 and 626941)

626992

Cable for connection to USB drive (included with handheld)

626990

ProDSS maintenance kit (included with all ProDSS 4-port cables):
• 3 port plugs
• 1 tube of o-ring lubricant
• 1 brush
• 1 syringe
• 1 sensor installation/removal tool
• O-rings (6)

626919

Sensor guard for 4-port ProDSS cable assembly (included with all 4-port cables)

599786

Calibration/storage cup for 4-port ProDSS cable assembly (included with all 4-port ProDSS cables)

627195

Calibration cup for ODO/CT cable assembly (included with all ODO/CT cables)

603062

Cable management kit (included with

ProDSS 4-port cables

10, 20, and 30-meters long;

ODO/CT

cables

4, 10, 20, and 30-meters long; and

ODO/T cables

4, 10, 20, and 30-meters long)

626918

1 lb weight (included with ProDSS 4-port cables 10-meters and longer)

605978

4.9 oz weight

ProDIGITAL Accessories

«
...
66
67
68
69
70
...
»

Summary of Contents for ProDIGITAL















































































Reviews:

No comments

Related manuals for ProDIGITAL

LM-OG-P2 Advanced

Brand: Badger Meter Pages: 48

Brand: Badger Meter Pages: 24

Brand: Bahco Pages: 92

Brand: E Instruments Pages: 2

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: M & I Instruments Pages: 2

Brand: Maico Pages: 27

Brand: Magnescale Pages: 14

Brand: VeEX Pages: 842

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brand: Vectornav Pages: 114

Electone Stagea ELS-01C

Brand: Yamaha Pages: 248

Brand: Stübbe Pages: 12

Brand: Energometrika Pages: 39

Brand: Rodstation Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands