YSI 85 Operation Manual Download Page 46

Page: 46 / 60

YSI, Incorporated

Model 85

APPENDIX A SPECIFICATIONS

Operating Environment

Medium: fresh, sea, or polluted water and most other liquid solutions.

Temperature: -5 to +65 °C

Depth: 0 to 10, 0 to 25, 0 to 50, or 0 to 100 feet (depending on cable length)

Storage Temperature:

-10 to +50 °C

Material:

ABS, Stainless Steel, and other materials

Dimensions:

Height:

9.5 inches

(24.13 cm)

Thickness:

2.2 inches

(5.6 cm)

Width:

3.5 inches max.

(8.89 cm)

Weight:

1.7 pounds (w/ 10’ cable)

(.77 kg)

Display:

2.3”W x 1.5”L

(5.8cm W x 3.8cm L)

Power:

9 VDC -6 AA-size Alkaline Batteries (included)

Approximately 100 hours operation from each new set of batteries

Water Tightness:

Meets or exceeds IP65 standards

Extensive testing of the YSI Model 85 indicates the following typical performance:

Measurement

Range

Resolution

Accuracy

Conductivity

0 to 499.9

S/cm

0.1

S/cm

.5% FS

0 to 4999

S/cm

1.0

S/cm

.5% FS

0 to 49.99 mS/cm

.01 mS/cm

.5% FS

0 to 200.0 mS/cm

0.1 mS/cm

.5% FS

Salinity

0 to 80 ppt

.1 ppt

2%, or

0.1 ppt

Temperature

-5 to +65 °C

0.1 °C

0.1 °C (

1 lsd)

Dissolved Oxygen

0 to 200 % Air Sat.

0.1% Air Saturation

2% Air Saturation

0 to 20 mg/L

0.01 mg/L

0.3 mg/L

Adjustable Conductivity Reference

Temperature

: 15°C to 25°C

Adjustable Temperature Compensation Factor for Conductivity:

0% to 4%

Temperature Compensation:

Automatic

Range:

Autoranging for Dissolved Oxygen

User selected or Autoranging for Conductivity

Summary of Contents for 85





























































Search results

Summary of Contents for 85

Reviews:

Brands by name

Popular brands

YSI 85, Operation Manual

Search results

Summary of Contents for 85

Reviews:

Brands by name

Popular brands