manualshive.com logo in svg

YSI 85, Operation Manual

Share
Download
YSI 85 Operation Manual Download Page 11

 

YSI, Incorporated 

Model 85 

7 

SECTION 3  PREPARING THE PROBE 

The YSI Model 85 dissolved oxygen probe is shipped dry. The protective membrane cap on 
the probe tip must be removed and replaced with KCl solution and a new membrane cap 
before using the probe. Follow the instructions below to install KCl solution and the new 
membrane cap. 
 

3.1  MEMBRANE CAP INSTALLATION 

To install a new membrane on your YSI Model 85 dissolved oxygen probe: 

1.

 

Unscrew and remove the probe sensor guard. 

2.

 

Unscrew and remove the old membrane cap. 

3.

 

Thoroughly rinse the sensor tip with distilled water. 

4.

 

Prepare the electrolyte according to the directions on the KCl solution bottle. 

5.

 

Hold the membrane cap and fill it at least 1/2 full with the electrolyte solution. 

6.

 

Screw the membrane cap onto the probe moderately tight. A small amount of  

 

          

electrolyte should overflow. 

7.

 

Screw the probe sensor guard on moderately tight. 

 

                        

                                         

                                                

                                             

Screw Cap  on

moderately tight

Unscrew Guard

Unscrew Cap

Fill Membrane
with KCL Solution

Screw Guard on

 moderately tight

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 85





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands