York ZJ078 Installation Manual Download Page 8

Page: 8 / 69

524581-YIM-I-0512

Johnson Controls Unitary Products

Units may be moved or lifted with a forklift. Slotted openings in
the base rails are provided for this purpose.

LENGTH OF FORKS MUST BE A MINIMUM OF 60 INCHES.

Figure 5: Unit 4 Point Load Weight

Figure 6: Unit 6 Point Load Weight

Figure 7: Center of Gravity

Before lifting, make sure the unit weight is distributed
equally on the rigging cables so it will lift evenly.

All panels must be secured in place when the unit is
lifted.

The condenser coils should be protected from rigging
cable damage with plywood or other suitable material.

LEFT

FRONT

LEFT

FRONT

LEFT

FRONT

Table 2:

Weights and Dimensions

Size

(Tons)

Model

Weight (lbs.)

Center of Gravity

4 Point Load Location (lbs.)

6 Point Load Location (lbs.)

Shipping Operating

078

(6.5)

1035

1030

245

191

260

333

170

144

122

167

195

232

090

(7.5)

1055

1050

250

195

265

340

174

146

125

170

199

236

102

(8.5)

1065

1060

247

184

268

360

173

141

117

171

206

253

120

(10)

1075

1070

245

191

278

357

170

143

122

178

209

248

150

(12.5)

1285

1280

240

281

410

350

156

173

192

280

252

227

Summary of Contents for ZJ078






































































Search results

Summary of Contents for ZJ078

Reviews:

Related manuals for ZJ078

Brands by name

Popular brands

York ZJ078, Installation Manual

Search results

Summary of Contents for ZJ078

Reviews:

Related manuals for ZJ078

Brands by name

Popular brands