York ZJ078 Installation Manual Download Page 41

Page: 41 / 69

524581-YIM-I-0512

Johnson Controls Unitary Products

Drive Selection

Determine side or bottom supply duct Application.

Determine desired airflow.

Calculate or measure the amount of external static pressure.

Using the operating point determined from steps 1, 2 & 3, locate this point on the appropriate supply air blower performance
table. (Linear interpolation may be necessary.)

Noting the RPM and BHP from step 4, locate the appropriate motor and, or drive on the RPM selection table.

Review the BHP compared to the motor options available. Select the appropriate motor and, or drive.

Review the RPM range for the motor options available. Select the appropriate drive if multiple drives are available for the
chosen motor.

Determine turns open to obtain the desired operation point.

Example

2600 CFM

1.6 iwg

Using the supply air blower performance table below, the following data point was located: 1268 RPM & 1.95 BHP.

Using the RPM selection table below, Size X and Model Y is found.

1.95 BHP exceeds the maximum continuous BHP rating of the 1.5 HP motor. The 2 HP motor is required.

1268 RPM is within the range of the 2 HP drives.

Using the 2 HP motor and drive, .5 turns open will achieve 1268 RPM.

Airflow Performance

Example Supply Air Blower Performance

Air Flow

(CFM)

Available External Static Pressure - IWG

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

2.0

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP

1.5 HP & Field Supplied Drive

Standard 1.5 HP & Drive

Alternate 2 HP & Drive

2200

804

0.50

866

0.71

925

0.90

982

1.06

1038

1.21

1092

1.35

1147

1.48

1203

1.61

1259

1.73

1317

1.87

2400

835

0.66

897

0.87

956

1.06

1013

1.22

1069

1.37

1124

1.51

1178

1.64

1234

1.77

1290

1.90

1348

2.03

2600

869

0.84

931

1.05

990

1.24

1047

1.40

1103

1.55

1158

1.69

1212

1.82

1268

1.95

1324

2.07

1382

2.21

2800

906

1.03

968

1.25

1027

1.43

1084

1.60

1139

1.75

1194

1.89

1249

2.02

1304

2.14

1361

2.27

Table X: RPM Selection

Size

(Tons)

Model

Max

BHP

Motor

Sheave

Blower

Sheave

6 Turns

Open

5 Turns

Open

4 Turns

Open

3 Turns

Open

2 Turns

Open

1 Turn

Open

Fully

Closed

1.5

1.73

1VM50

AK74

N/A

897

945

991

1035

1079

1126

2.30

1VM50

AK64

N/A

1039

1094

1150

1207

1256

1308

Summary of Contents for ZJ078






































































Search results

Summary of Contents for ZJ078

Reviews:

Related manuals for ZJ078

Brands by name

Popular brands

York ZJ078, Installation Manual

Search results

Summary of Contents for ZJ078

Reviews:

Related manuals for ZJ078

Brands by name

Popular brands