background image

3

Safety Precautions

Be sure to conform with the following important Safety Precautions.

Carefully read the following information in order to operate the air conditioner correctly.

If any abnormal phenomena is found

(e. g.smell of firing), please cut off

the power supply immediately, and

contact the dealer to find out the

handling method.

In such case, to continue using the conditioner will damage

the conditioner, and may cause electrical shock or fire

hazard.

Don't dismantle the outlet of the

outdoor unit.

The exposure of fan is very dangerous

which may harm human beings.

Symbols used in the illustrations

:Indicates an action that must be avoided.

:Indicates that important instructions must be followed.

:Indicates a part which must be grounded.

:Beware of electric shock (This symbol is displayed on the main unit label.)

After reading this handbook, hand it over to those who will be using the unit.

The user of the unit should keep this mamual at hand and make it available to those who will be performing repairs or

relocating the unit. Also, make it available to the new user when the user changes hands.

Below are listed three kinds of Safety Precautions and Suggestions.

Incorrect operations may result in severe consequences of death or serious injuries.
Incorrect operations may result in injuries or machine damages; in some cases may

cause serious consequences.

INSTRUCTIONS: These information can ensure the correct operation of the machine.

After a long time use of air-conditioner

the base should be checked for any

damages.

If the damaged base is not repaired, the

unit may fall down and cause accidents.

When need maintenance and repairment,

call dealer to handle it.

Incorrect maintenance and repairment

may cause water leak, electrical shock

and fire hazard.

Air-conditioner can't be installed in the environment with

inflammable gases because the inflammable gases near

air-conditioner may cause fire hazard.

Please let the dealer be responsible for installing the

conditioner. Incorrect installation may cause water leak,

electrical shock and fire hazard.

Connect earthing wire.

Earthing wire should not be connected to the gas

pipe, water pipe, lightning rod or phone line,

incorrect earthing may cause shock.

Use discharge pipe correctly to ensure efficient discharge.

Incorrect pipe use may cause water leaking.

Installed electrical-leaking circuit breaker.

It easily cause electrical shock without circuit breaker.

Call the dealer to take measures to prevent the refrigerant

from leaking.

If conditioner is installed in a small room, be sure to take

every measure in order to prevent suffocation accident

even in case of refrigerant leakage.

When conditioner is installed or reinstalled, the dealer should

be responsible for them.

Incorrect installation may cause water leaking, electrical

shock and fire hazard.

No goods or nobody is permitted to

placed on or stand on outdoor unit.The

falling of goods and people may cause

accidents.

Don't operate the air-conditioner with

damp hands.Otherwise it will be shocked.

Only use correctly-typed fuse.

May not use wire or any other materials

replacing fuse, otherwise it may cause

faults or fire accidents.

Earthing

switch off

!

WARNING
CAUTION

WARNING

WARNING

Summary of Contents for YHUJYH(024-060)BAR(S)XA-X(Y)





















Reviews: