246653-YTG-E-0108
8
Johnson Controls Unitary Products
LIST OF FEATURES AND BENEFITS
Standard Features
•
9.5 EER (10 EER on 25 ton)
•
Double wall construction
•
Major components have hinged and latched access
doors
•
Industrial duty scroll compressors
•
Sturdy framed construction
•
Sloped stainless steel or powder coated drain pan
•
Separate 10 ton circuits (30 and 40 ton units) or 12.5 ton
(25 ton unit)
•
Intertwined evaporator coil
•
Angled condenser coils for superior protection
•
Single power point connection
•
Through-the-curb or through-the-base utility connections
•
Retractable outside air hoods
•
Powder paint tested to 1000 salt spray hours
•
Mechanical cooling from 40° F to 125° F
•
1-1/2” insulation
•
Sloped unit roof with drip lip
•
High and low refrigerant pressure protection
•
Polyurethane sleeves to protect small diameter tubing
•
Steel framing around blowers with deflection springs or
rubber isolators for low vibration
•
Fully factory packaged and run-tested
•
10 year gas heat exchanger warranty
•
One year compressor warranty
•
One year warranty on all parts
Factory Installed Options
•
Economizer with standard or low leak dampers
•
Natural gas standard or modulating gas heat with reli-
able induced draft design
•
Electric heat in three sizes
•
Variable air volume using either inlet guide vanes, wired
for VFD (variable frequency drive), or factory installed
VFD.
•
1, 2” blower isolator springs or rubber isolators
•
A variety of blower horsepower offerings
•
High efficiency motors
•
High efficiency filtration
•
Barometric relief
•
Power exhaust of 100% of nominal air flow
•
Technicoat corrosive resistant coating on condenser and
evaporator coils
•
Copper-Copper corrosive resistant condenser and evap-
orator coils
•
0°F low ambient operation of mechanical cooling
•
Hot gas bypass (standard on all VAV units)
•
High capacity evaporator coils
•
Single unit disconnect
•
Convenience outlet and transformer factory wired
•
Hot water heating coil with one or two rows
•
One row steam heating coil
•
Simplicity
®
Elite™ controls
•
ModLINC translator
•
York Commercial Comfort System (YCCS)
Field Installed Accessories
•
7-Day Programmable Wall Thermostat-Can be used with
or without remote sensors. Can be used on CV and VAV
units when wall thermostat is required for scheduling and
temperature control.
•
Energy Recovery Ventilators- 8,000 and 13,000 CFM
models available. Great for applications involving 30% or
more of required outdoor air where energy use and com-
fort must be optimized.
•
Wall Sensors- Remote space sensors used with CV or
VAV unit for unit control via the Simplicity® Elite™ con-
trol. Standard sensor, sensor with override and sensor
with override and + 5 degree adjustment.
•
Simplicity® Transporter- Device allows internet control
and monitoring of HVAC units equipped with Simplicity®
Elite™ controls.
•
Phase Monitor Kit- Includes control and wiring to monitor
and protect the unit from phase reversal, phase loss and
low voltage.
•
Burglar Bars- Prevent any type of building entry through
the RTU unit with bars that block the return and supply
openings on downflow applications.
•
Partial perimeter roofcurb- Designed for application on
all 25-40 ton Millennium rooftop units. 14" height.
•
Barometric Relief Kit- Provides barometric relief hood
and dampers for duct mounting on units requiring end
return.
•
Natural Gas to Propane Conversion Kits- Contains ori-
fices and gas valves parts to convert from Natural Gas to
Propane. (Not available on modulating heat.)
•
High Altitude Kit- Natural gas kit designed for natural gas
heating applications between 2,000 and 6,000 feet
above sea level.
