background image

FAN SPEED CONTROLLER

1      2      3     4

1

3

4

9

7

8

2

5

6

95

100

4- ø5.4

Note : For very low temperature operation in cooling mode we

recommend  to  set  the  Changeover  Switch

  to  ‘cut-off’

position.

NO.

1.
2.
3.
4.
5.
6.
7.
8.
9.

Parts Name

Bellows
Wiper
Operating Plate
Range Adjusting Screw
Coil Spring
Terminal Board
Changeover Switch
Pressure Connector
Range Setting Pointer

Indoor unit

Copper Packing

Cut

Off

Min

Speed

Slide Potentiometer

(CW)

Increase the

set valve

Decrease the

set valve

(CCW)

Capillary Tube

(900 mm Length)

Conduit Gland

1/4 Female Flare with Schrader

COOLING CIRCUIT - PRESSURE TAP LOCATION

PRESSURE TAP

Outdoor unit

C a u t i o n

Risk of electric shock

A fan speed controller is provided as standard on full featured condensing units and can be installed also as an accessory in the

field  on  all  N  series  condensing  units  that  are  equipped  with  a  pressure  tap  (see  diagram  below)  for  easy  installation. The

Saginomiya pressure type controller (YORK P/N 025T20003-000) is recommended. Fan speed controllers should be added when

the units are installed where operation in cool mode is required during periods with low outdoor ambient temperatures. Complete

installation instructions are included with every fan speed controller kit ordered from the factory.

Summary of Contents for MOC-MOH 07-65













Reviews: