9
ENGLISH
EN
ø 65 mm
PARTS INSTALLATION
Mounting screw B
ST3.9x10-C-H
Remote controller
holder
Loop the
connective
cable.
8
9
Remote Controller
7
C
B
A
60cm or more
30cm
or m
ore
6
0c
m o
r mo
re
200
cm o
r m
ore
6
2
3
1
12cm or m
ore
12cm or
more
Air Filter
15cm or more
Air Outlet
30cm
or
mo
re
On/Off
Sleep
Fan
Swing
Air Direction
Timer On
Timer Off
Mode
Hr.
ON
TIMER
Hr.
Off TIMER
SET TEMP
Auto
Number
1
2
3
4
5
Connecting
pipe
Assembly
Liquid side
Gas side
Name of Accessories
Q’ty
Installation plate
Clip anchor
Self-tapping screw A ST3.9X25
Seal
Drain joint
1
8
8
1
1
ø6.35
Parts you
must
purchase
ø 9.53 (9000Btu/h model)
ø12.7(12000Btu/h model)
Remote controller
Self-tapping screw B ST3.9X10
Remote controller holder
7
8
9
1
2
1
INDOOR UNIT
INSTALLATION PROCEDURE
■
Fixing
• Place the installation guide pattern on the designated
installation place and mark the hole position.
• Drill a hole and mount installation plate.
MODEL 07-09
• Make 6 mm 4-6 holes, in the wall at the four corners of mounting
plate (bracket) then insert appropriate mounting devices.
• Install the mounting plate using 4-6 pieces of mounting screw
securely at four corners and tighten the screw completely.
Do not over tighten the screws and deform the back plate.
Installation Plate
Outline of the Indoor Unit
Rear-right Pipe
Hole 65
270~370
878
659
133
40
40
270
27
6
55
55
39
Rear-right Pipe
Hole 65
Above 15cm from the ceiling
Above 15cm from the ceiling
Above 12cm
from the wall
Above 12cm
from the wall
Above 12cm
from the wall
Above 12cm
from the wall
Rear-left Pipe
Hole 65
Rear-left Pipe
Hole 65
Installation Plate
Outline of the Indoor Unit
70
70
45
250
750
Except the above parts provided, the other parts needed
during installation you must purchase.
• Ensure that the space around the left and right of the
indoor unit is more than 12cm.
The indoor unit should be installed allowing a minimum
clearance of 15cm from the ceiling.
• Use a stud finder to locate studs to prevent unnecessary
damage to the wall.
• A minimum pipe run of 3 metres is required to minimise
vibration & excessive noise.
The indoor unit should be installed on the wall at a
height of 1.7 metres or more from the floor but less
than 2.3 metres from the floor.
• Directions A, B and C should be free from obstructions.
NOTES
CAUTIONS
NOTES
• This illustration is for explanation purposes only.
• Copper lines must be insulated independently.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
• After determining the pipe
hole position. Drill the hole
at a slight downward slant
towards the outdoor side.
Outdoor
Indoor
Note: When installing
the refrigerant pipes from
others side. A hole must
be place to allow fall
towards the outdoor unit.
MODEL 12
J190
2/03/2005, 4:55 AM
9
