PARTS INSTALLATION
Part No.
Name of part
Q’ty
1
Installation plate
1
2
Mounting screw ST3.9x25-C-H
8
3
Clip anchor
8
Refrigerant
Liquid side
Parts you
4
must
pipe
Gas side
purchase
5
Remote controller
1
6
Remote controller holder
1
7
Seal
1
8
Drain elbow
1
NOTE: At least two of A, B, C aspect are free from blocking.
The air-conditioner can be connected only to a supply
with system impedance no more than 0.26 ohm. In
case necessary please consult your supply authority
for system impedance information.
■
Cautions on remote controller installation
•
Before installation, operate the remote controller to
determine its location in a reception range.
•
Keep the remote controller at least 1 m apart from the
nearest TV set or stereo equipment.
•
Do not install the remote controller in a place exposed to
direct sunlight or close to a heating source, such as a stove.
•
Note that the positive and negative poles are right
positions when loading batteries.
12cm
15cm or more
or
more
1
2
3
12cm
or
more
Air
filter
Mounting screw B
ST2.9x10-C-H
6
4
Remote controller
holder
5
Remote controller
o
re
Air blowing
m
o
r
c
m
10cm
direction
or
6
0
A
more
ormore
10cm
ore
m
or
B
100cm
60cm
or
more
C
Loop the
connective
cable.
INSTALLATION PROCEDURE
INDOOR UNIT
■
Fixing
•
Place the installation guide pattern on the designated
installation place and mark the hole position.
•
Drill a hole and mount installation plate.
•
Make 6 mm 4-6 holes, in the wall at the four corners of mouting
plate (bracket) then insert appropriate mounting devices.
•
Install the mounting plate using 4-6 pieces of mounting screw
securely at four corners and tighten the screw completely. Do
not over tighten the screws and deform the back plate.
MODEL 07-09, 12 [220-240V, 50/60Hz]
ø 65 mm
Indoor unit outline
20
12 cm or more
to wall
Left
refrigerant
pipe hole
ø65 mm
15 cm or more to
ceiling
Installation plate
30
250
12 cm or more
to wall
45
70
Right refrige-
750
rant pipe hole
ø65 mm
• After determining the pipe
hole position drill the hole
at
MODEL 12 [115V, 60Hz (UL)]
a slight downward slant
towards the outdoor side.
Note: When installing
the refrigerant pipes from
Indoor
others side. A hole must
be place to allow fall
towards the outdoor unit.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Outdoor
Indoor unit outline
12 cm or more
to wall
280
Left
refrigerant
pipe hole
ø65 mm
15 cm or more to
ceiling
815
Installation plate
12 cm or more
to wall
50
50
Right refrige-
rant pipe hole
ø65 mm
8
ENGLISH
J174_lastRev4.pmd
8
3/14/05, 3:27 PM
