background image

PLEASE READ THIS INSTRUCTION MANUAL BEFORE YOU BEGIN ASSEMBLY.  GREAT 

CARE HAS BEEN TAKEN TO DESIGN THESE INSTRUCTIONS AND FOLLOWING THEM 

WILL HELP YOU WITH QUICKER ASSEMBLY AND MINIMISE THE RISK OF INJURY

YOU ARE RESPONSIBLE FOR YOUR OWN SAFETY - 

THIS LIST IS NOT EXHAUSTIVE.
•  Always assemble and operate 

the product on a level surface

•  Always use the product on a level surface, 

ensure that the product is stable before use.

•  Always ensure that the equipment has adequate space 

on each side and front (the back can be near to a wall).

•  Ensure that the seat height is adjusted correctly - you 

should be stable and balanced whilst on the saddle.

•  Adjust the seat height to ensure that you have a good 

downward pedal stroke without overstretching, don’t 

compromise your balance.

•  Try to ensure that your back is straight whilst exercising, 

especially for long periods

•  The safety level of this equipment can only be maintained 

only if it is regularly examined for wear and tear.

•  Replace defective components immediately, and/or 

keep the equipment out of use until it is repaired.

•  Use only the adjustment settings as described in the 

instructions.  Always use the correct adjustment pin/fixing.

•  Always check that any pins / fixings are tight and 

secure before use and / or after adjustment. 

•  Never leave any adjustment devices 

projecting from the product.

•  Always consult your doctor before 

undertaking any exercise program.

•  Always wear suitable clothing and footwear 

e.g. tracksuit / shorts / training shoes

•  Remove all personal jewellery before exercising.

•  Ensure you warm-up well before using the 

equipment as this will help to prevent muscle strain.

•  After eating, allow 1-2 hours before exercising as 

this will help to prevent muscle strain.

•  Never overload the equipment – the maximum 

user weight of this cycle is 150kg.

•  Never use the equipment in any other manner other 

than the ways explained in these instructions and/or 

any wall-chart supplied.

•  Injuries to health may result from incorrect or 

excessive training.

•  Parents and others in charge of children should be aware 

of their responsibility, because the natural play instinct 

and the fondness of experimenting of children can lead to 

situations and behaviour for which the training equipment 

is not intended

•  If children are allowed to use the equipment, 

their mental and physical development and above all 

their temperament should be taken into account. They 

should be controlled and instructed in the correct use 

of the equipment.  

•  The equipment is under no circumstances 

suitable as a children’s toy.

•  Children should not be allowed on, or around 

the equipment - especially when it is not in use.

•  This appliance is not intended for use by persons 

(including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, 

unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible 

for their safety.

Safety Standards

This cycle meets the requirements of the EU’s EMC and Low Voltage directives (where applicable),  

ISO 20957 parts 1 and 5 and AS 4092-1993.  Therefore the product carries the following marks:

4

It is important that you keep these instructions for future reference.

!

This product is not suitable for therapeutic purposes.

safety information

Summary of Contents for diamond c302





















Reviews: