manualshive.com logo in svg

YOKOGAWA WE7281, User Manual, Page: 36 / 52

Share
Download
YOKOGAWA WE7281 User Manual Download Page 36

3-11

IM 707281-01E

Software Operation

3

Selecting the Output Mode

Select the output mode with the [Output Mode] option buttons.  The choices are shown

below.  The default is [Cont].

Cont: Continuous oscillation

Continuously outputs the waveform from the time the output is turned ON by clicking the

[Output] button until the output is turned OFF by clicking the [Output] button again.

Trigger: Trigger oscillation

After the [Output] button is clicked to turn ON the output, the waveform is continuously

output when a trigger occurs.  This continues until the output is turned OFF by again

clicking the [Output] button.

Gate: Gate oscillation

After the [Output] button is clicked to turn ON the output, the oscillation starts when the

gate is enabled.  When the gate is disabled the oscillation stops.  The waveform output

unit is one cycle.

Note

When the output is OFF, the waveform output terminal of the module outputs 0 V.

3.4  Setting the Output Condition in the FG Mode

Summary of Contents for WE7281





















































Reviews:

No comments