YOKOGAWA Rotamass Giga General Instruction Manual Download Page 2

Page: 2 / 90

Table of contents

2 / 90

IM 01U10B00-00EN-R, 3rd edition, 2018-07-09

Table of contents

Introduction................................................................................................................................................

1.1

Scope of application .........................................................................................................................

1.2

Target group .....................................................................................................................................

1.3

Applicable documents.......................................................................................................................

1.4

Explanation of safety instructions and symbols ................................................................................

Safety..........................................................................................................................................................

2.1

Intended use .....................................................................................................................................

2.2

Technical conditions .........................................................................................................................

2.3

General safety instructions ...............................................................................................................

Warranty .....................................................................................................................................................

Product specification ................................................................................................................................ 10

4.1

Scope of delivery ..............................................................................................................................

4.2

Measuring principle and flow meter design ......................................................................................

4.2.1

Measuring principle .............................................................................................................. 11

4.2.2

Flow meter ........................................................................................................................... 13

4.3

Identification......................................................................................................................................

4.3.1

Nameplates .......................................................................................................................... 14

4.3.2

Model code .......................................................................................................................... 17

4.4

Flow meter components ...................................................................................................................

4.5

Mechanical specification...................................................................................................................

Transport and storage .............................................................................................................................. 19

5.1

Transport ..........................................................................................................................................

5.2

Storage .............................................................................................................................................

Installation.................................................................................................................................................. 21

6.1

Installation instructions .....................................................................................................................

6.1.1

Installation dimensions......................................................................................................... 21

6.1.2

Installation site ..................................................................................................................... 21

6.1.3

Instructions........................................................................................................................... 22

6.1.4

Installation position .............................................................................................................. 23

6.1.5

Sanitary Installation.............................................................................................................. 24

6.2

Installation instructions .....................................................................................................................

6.3

Sensor installation ............................................................................................................................

6.3.1

General installation rules ..................................................................................................... 27

6.3.2

Installation in pipe ................................................................................................................ 28

6.3.3

Installation Rotamass Nano (Option PD) ............................................................................. 30

6.3.4

Installation recommendation for viscosity measurements ................................................... 31

6.4

Insulation and heat tracing................................................................................................................

6.4.1

Heat tracing.......................................................................................................................... 32

6.4.2

Customer-supplied insulation............................................................................................... 32

6.5

Transmitter installation......................................................................................................................

6.5.1

Rotating and replacing the display ....................................................................................... 33

6.5.2

Rotating transmitter housing (integral type) ......................................................................... 36

6.5.3

Rotating the terminal box (remote type)............................................................................... 38

6.5.4

Installing transmitter on pipe (remote type).......................................................................... 39

Summary of Contents for Rotamass Giga



























































































Search results

Summary of Contents for Rotamass Giga

Reviews:

Related manuals for Rotamass Giga

Brands by name

Popular brands

YOKOGAWA Rotamass Giga, General Instruction Manual

Search results

Summary of Contents for Rotamass Giga

Reviews:

Related manuals for Rotamass Giga

Brands by name

Popular brands