YOKOGAWA RAMC User Manual Download Page 10

Page: 10 / 136

<1. INTRODUCTION>

1-2

IM 01R01B02-00E-E 12th edition October 01, 2014 -00

1.1 For Safe Use of Rota-

meter RAMC

(0) General

• Working with bare skin should not be done.
• Working with wet hand, body should not be

done.

(1) Installation

• Installation of the RAMC variable area flowme

ter must be

performed by expert engineer or skilled

personnel.

operator shall be permitted to

perform procedures relating to installation.

• The RAMC flowmeter is a heavy instrument.

Be careful that no damage is caused to personnel

through accidentally dropping it, or by exerting

excessive force on the RAMC flowmeter.
•

All procedures relating to installation must comply
with the electrical code of the country where it
is used.

(2) Wiring

• The wiring of the RAMC flowmeter must be

per-

formed by expert engineer or skilled personnel. No

operator shall be permitted to perform

procedures relating to wiring.

• When connecting the wiring, check that the

supply voltage is within the range of the voltage
specified for this instrument before connect-
ing the power cable. In addition, check that
no voltage is applied to the power cable before
connecting the wiring.

• The protective grounding must be connected

securely at the terminal with the mark to
avoid danger to personnel (only AC type).

(3) Operation

• Do not open the cover until the power has been

off for at least 10 minutes because of electric

shock and hot temperatures inside. Only expert

engineer or skilled personnel are permitted to
open the cover.

• When the RAMC flowmeter is processing hot

fluids, the instrument itself may become ex

tremely hot. Take sufficient care not to get

burnt.

If the fluid temperature is above 65°C it has to

be ensured, that an easy touch by humans is
prohibited (e.g. by installation, by a barrier, by a
warning).

WARNING

• Where the fluid being processed is a toxic sub

stance, avoid contact with the fluid and avoid

inhaling any residual gas, even after the instru-
ment has been taken off the line for

maintenance and so forth.
(4) Maintenance

• Maintenance on the RAMC flowmeter should be

performed by expert engineer or skilled person

nel. No operator shall be permitted to perform

any operations relating to maintenance.

• Always conform to maintenance procedures

outlined in this manual. If necessary, contact
Yokogawa.

• Care should be taken to prevent the build up

of dirt, dust or other substances on the display
panel glass. If these surfaces do get dirty, wipe
them clean with a soft dry cloth.

• Don’t open the cover in rainy weather
• Don’t open the cover during power is connected

because of electric shock.

• The electronic assembly contains sensitive

parts. Take care so as not to directly touch the

electronic parts or circuit patterns on the board,
and by preventing static electrification using
grounded wrist straps when handing the

assembly.

(5) European Pressure Equipment Directive

(PED)

• When using the instrument as a PED-compliant

product, be sure to read Chapter 11 before use.

(6) Hazardous Duty Type Instruments

• For explosion proof type instruments the

description in chapter 10 "

EXPLOSION PRO-

TECTED TYPE INSTRUMENT

" has priority to

the other descriptions in this instruction manual.

• All instruction manuals for ATEX Ex related

products are available in English, German and

French. Should you require Ex related instruc

tions in your local language, you should contact
your nearest Yokogawa office or representative.

• Only trained personal should install and

maintain instruments in hazardous areas.

Summary of Contents for RAMC




























































































































Search results

Summary of Contents for RAMC

Reviews:

Related manuals for RAMC

Brands by name

Popular brands

YOKOGAWA RAMC, User Manual

Search results

Summary of Contents for RAMC

Reviews:

Related manuals for RAMC

Brands by name

Popular brands