manualshive.com logo in svg

YOKOGAWA FLXA21, User Manual

Share
Download
YOKOGAWA FLXA21 User Manual Download Page 39

 

 

<6.  Function block parameters and Methods>

6-13

IM 12A01A02-72E

3rd Edition : Oct. 01, 2015-00

6.4 

Diagnostic Information

n

 DIAGNOSIS

Diagnostic information and failures are indicated by using parameter Diagnosis and Diagnosis 

Extension in the Physical Block.
DIAGNOSIS has Classic DIAGNOSIS and Condensed DIAGNOSIS. Classic DIAGNOSIS is 

a conventional alarm and does not support the NAMUR NE107. Condensed DIAGNOSIS is 

an alarm which was added to PA Profile 3.01 or later and supports the NAMUR NE107. For 

switching the two statuses, refer to “

n

  Status of Each Parameter in Failure Mode” on page 

5-1.

Contents of condensed DIAGNOSIS and classic DIAGNOSIS are listed in Table 6.1 and 6.2.

Table 6.1  Contents of Condensed DIAGNOSIS

Octet Bit

DIAGNOSIS 

Mnemonic

Description

Remarks

NAMUR 

NE107 

Category

1

0-7 Reserved *2

Reserved for use within the PNO

—

—

2

0-3 Reserved *2

Reserved for use within the PNO

—

—

3 DIA_WARMSTART *1 New start-up (warm startup) 

carried out.

Should be set after power-on 

or after FACTORY_RESET = 

2506 has been executed.

—

4 DIA_COLDSTART *1 Restart (cold startup) carried out. Should be set after 

FACTORY_RESET = 1 has 

been executed.

—

5 DIA_MAINTENANCE 

*2

Maintenance required

—

M

6 Reserved *2

Reserved for use within the PNO

—

—

7 IDENT_NUMBER_

VIOLATION *2

Set to 1 (one), if the IDENT_

Number of the running cyclic 

data transfer and the value 

of Physical Block IDENT_

NUMBER_SELECTOR 

parameter do not correspond.

If IDENT_NUMBER_

SELECTOR = 127 (adaption 

mode) then the DIAGNOSIS bit 

IDENT_NUMBER_VIOLATION 

is cleared / not set.

—

C

3

0 DIA_MAINTENANCE_

ALARM

Failure of the device or armature Refer to Table of Device 

status.

F

1 DIA_MAINTENANCE_

DEMANDED *2

Maintenance demanded

Refer to Table of Device 

status.

M

2 DIA_FUNCTION_

CHECK

Device is in function check mode 

or in simulation or under local 

control e.g. maintenance

Refer to Table of Device 

status.

C

3 DIA_INV_PRO_COND The process conditions do not 

allow to return valid values. 

(Set if a value has the quality 

Uncertain - Process related, no 

maintenance or Bad - Process 

related, no maintenance

Refer to Table of Device 

status.

S

4-7 Reserved *2

Reserved for use within the PNO

—

—

4

0-6 Reserved *2

Reserved for use within the PNO

—

—

7 EXTENSION_

AVAILABLE

0: There is no more information 

available

1: More diagnosis information 

is available in DIAGNOSIS_

EXTENSION

—

—

*1: 

This bit is Off 10 seconds after On.

*2: 

Not available for FLXA21.

Summary of Contents for FLXA21

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands