YOKOGAWA FLXA202 User Manual Download Page 73

Page: 73 / 274

<4. COMMISSIONING OF pH/ORP>

4-5

IM 12A01A02-01E

8th Edition : Oct. 01, 2015-00

Matrix

Matrix means a temperature compensation which uses the temperature compensation

matrix. The temperature compensation matrix is a table of pH values at various temperatures

corresponding to the pH values at the standard temperature. For details, see Appendix 1.

When the temperature or the precompensated pH value is out of the range of the temperature

compensation matrix, the temperature compensation error (warning) will be issued. This is not a

device error.

In this case, however, the temperature compensation is performed by extrapolation.

NOTE

To display the precompensated pH value, set the Process Temp. Compensation to “None”.

Select Measurement setup → Temp. compensation → Process Temp. Compensation.

NEN6411

This algorithm takes into account the dissociation of water in strong acid and strong alkaline

solutions. It is particularly useful for pH measurement of boiler feed water.

4.2.4

Calibration settings

The screen flow differs depending on the combination of objects to be measured.

Calibration settings for a pH converter involve slope (sensitivity), zero (aspot), and ITP

(isothermal point). Figure 4.2 shows the pH value against the mV output of the sensor. The

characteristic for pH measurement is an offset also known as aspot [mV] or zero [pH] and a

Slope [%, mV/pH]. For an ideal sensor, the theoretical slope is 59.16 mV/pH at 25ºC. The slope

can be entered in mV/pH or as a percentage of the theoretical slope (100% corresponds to

59.16 mV/pH). ITP represents a pH value where the output of the sensor does not change with

temperature. Note that slope and zero are defined at 25ºC.

ΔpH

ΔmV

ITP (Isothermal point)

Aspot

0 mV

0 °C

10 °C

25 °C

500

- 200

ITP Zero

Figure 4.2

Calibration parameters

pH settings

Zero and Slope units

Zero is an alternative to Asymmetry Potential. The method of zero (aspot) unit conforms to the

DIN standard for IEC 60746-2 instruments. Zero is defined in pH or mV.
The unit of Slope (sensitivity) is mV/pH or % (with the theoretical value as 100%).

Summary of Contents for FLXA202



















































































































































































































































































Search results

Summary of Contents for FLXA202

Reviews:

Related manuals for FLXA202

Brands by name

Popular brands

YOKOGAWA FLXA202, User Manual

Search results

Summary of Contents for FLXA202

Reviews:

Related manuals for FLXA202

Brands by name

Popular brands