6-3
IM AQ6370E-02EN
Specifications
1
2
3
4
5
6
App
Index
Item
Specifications
Standard Model (-10)
High performance model (-20)
Emissions Compliant
standards
EN 61326-1: Class A Group 1
16
Table 2
EN 61000-3-2
EN 61000-3-3
EMC Regulatory Arrangement in Australia and New Zealand EN 61326-1: Class A
Group 1 Table 2
Korea Electromagnetic Conformity Standard (
한국 전자파적합성기준
)
This product is classified as Class A (for use in industrial environments). Operation of
this product in a residential area may cause radio interference, in which case the user
will be required to correct the interference.
Cable
conditions
• Ethernet connector
Use category 5 or better Ethernet cables.
17
• VIDEO OUT connector
Use a shielded D-sub 15 pin VGA cable.
17
• USB port
Use USB peripherals (e.g., mouse) with shielded USB cables.
17
• GP-IB interface connector
Use a shielded GP-IB cable.
17
• TRIGGER IN, TRIGGER OUT, ANALOG OUT terminal
Use a BNC cable.
17
Immunity Compliant
standards
EN 61326-1 Table 2
Influence in the immunity environment (criteria A)
Wavelength measurement accuracy: ±0.1 nm
Cable
conditions
The same as the cable conditions listed above for emissions
Environmental standards
18
EU RoHS Directive compliant
1 Horizontal axis scale: In wavelength display mode
2 9.5/125 μm single mode fiber (PC polishing), after warm-up of 1 hours, after alignment with a built-in wavelength reference
light source or single longitudinal mode laser (wavelength: 1520 to 1560 nm, peak level: –20 dBm or higher, level stability: 0.1
dBpp or less, wavelength stability: ±0.01 nm or less)
3 Vertical scale: absolute value level display mode, resolution setting: 0.05 nm or more, resolution correction: OFF
4 When using 9.5/125 μm single mode fiber (SSMA type in JIS C6835, PC polishing, mode field diameter: 9.5 μm, NA: 0.104 to
0.107)
5 After wavelength calibration using a built-in wavelength reference light source or single longitudinal mode laser (peak level:
–20 dBm or higher, absolute waveform accuracy in the wavelength range of 1520 to 1560 nm ± 0.003 nm or less)
6 With the resolution setting of 0.05 nm, at ambient temperature of 23 ±3 °C.
7 High dynamic mode: OFF, pulse light measurement mode: OFF, resolution correction: OFF
8 1523 nm, high dynamic mode:SWITCH, resolution correction: OFF
9 Span 100 nm or less, wavelength sampling points: 1001, averaging times: 1
10 When applying a HeNe laser (1523 nm), resolution: 0.1 nm, 1520 nm to 1620 nm (excluding peak wavelength ± 2 nm).
11 When using the Yokogawa signal mode fiber with our standard Angled PC connector, it is 15 dB(Typ.) when using the PC
connector.
12 Certain commands may not support the AQ6317 depending on the relationship between the target model specifications and
functions.
13 The LDC display may contain defective pixels (always ON or always OFF). (0.002% or fewer of all pixels including RGB).
Does not indicate a general malfunction.
14 The overvoltage category is a value used to define the transient overvoltage condition and includes the rated impulse
withstand voltage. Category II applies to electrical equipment that is powered through a fixed installation, such as a wall outlet
wired to a distribution board.
15 Pollution degree refers to the degree of adherence by a solid, liquid, or vapor that reduces the withstand voltage or surface
resistance factor. Pollution degree 1 applies to closed atmospheres (no pollution, or only dry, non-conductive pollution).
Pollution degree 2 applies to normal indoor atmospheres (with only non-conductive pollution).
16 Group 1: Equipment that does not intentionally generate or use radio-frequency (RF) energy
17 Use a cable of 3 m in length or less.
18 For conformity to environmental regulations and/or standards other than EU, contact your nearest YOKOGAWA office
(PIM113-01Z2).
*: Typical values(typ.) are typical or mean values. They are not strictly guaranteed.
6.1 Signal Input Section
