9
8
EN
EN
9.b
9.a
Adjusting the angle of the brake levers
On both brake levers loosen the screw
on the sleeve. For the best results, stand
on the footrest, grab the handlebars and
stretch your fingers so they extend the
straight line of your hands. Set the brake
levers in this position and tighten the
two mounting screws.
You can adjust the position of the
corners on the Yedoo Wolfer model
using the mounting screws on the
picture.
Check the brake pads if they moved
away from the rim sufficiently (1–2 mm)
when the brake lever is released.
Distance of the brake pads can be
adjusted by tightening or releasing of
the brake wire anchor bolt (
1
). If the
wheel during the rotation crossed the
brake pad at some point, adjust the
distance of the brake arms symmetrically
with tensioning bolts (
2
).
Adjusting the rear brake
is the same for
both models.
Insert the brake wire back into the guide
(
1
). Check the brake pads during braking
if their entire surface fit tightly to the
side of the rim. If not, adjust the screw
(
2
), which attaches the brake pads to
the shoulders of V- brakes. Brake Shoes
must not touch the tyre.
Check the brake pads if they moved
away from the rim sufficiently (1–2 mm)
when the brake lever is released.
Distance of the brake pads can be
adjusted by tightening or releasing of
the brake wire anchor bolt (
1
). If the
wheel during the rotation crossed the
brake pad at some point, adjust the
distance of the brake arms symmetrically
with tensioning bolts (
2
).
8.
Installing brake wires
Squeeze the brake lever to the maximum
and insert the end of the brake wire into
the round lug (
1
) Insert the wire into the
groove and tighten the set screw (
2
)
and the nut (
3
). Repeat the process with
the other brake. The rear brake wire is
usually mounted to the right brake lever
and the front brake wire to the left.
1
2
12.
13.
11.b
1
1
1
2
2
2
2
2
2
3
10.b
Adjusting the front brakes – Wolfer
The entire surface of the brake pads
should fit tightly to the side of the rim
while braking. If not, adjust the position
of the brake pads using the screws,
which attaches the brake pads to the
arms of the brake (
1
). The pads may
not touch the tyre and while the brake
levers are released they should be
1–2 mm away from the rim. The distance
of the brake pads can be adjusted by
tightening or releasing of the brake wire
in the anchor bolt (
2
).
If the wheel touches the brake pad at
some point during the rotation, turn the
whole brake mechanism until the brake
arms are evenly spaced from the rim.
To lock the position of the arms, turn the
lever downwards (
1
).
11.a
14.b
14.a
Adjusting the bowden cables
Adjust the position of the cables
and make sure they do not exceed
over the frame of the scooter
(especially in the rear fork area).
Attach them to the socket in front of
the frame.
Adjusting the front brakes – Trexx
Insert the brake wire back into the guide
(
1
) and check the brake pads during
braking if their entire surface fits tightly
to the side of the rim. If not, adjust the
brake shoes position with the screw (
2
),
which attaches the brake pads to the
shoulders of V-brakes. Brake pads must
not touch the tyre.
15.
Anti-slip tapes
Use the spare anti-slip tapes to enhance
the anti-slip effect of the footrest. Easily
stick the into the empty slots of the
footrest.
Caution:
Clean and degrease
the footrest thoroughly before the
installation.
1
2
2
10.a
2
1
1
1
6–7 Nm
6–7 Nm
Installation manual
Summary of Contents for Wolfer
