Yeastar Technology NeoGate TA410 User Manual Download Page 33 | Manualshive

Page: 33 / 55

background image

TA410/810 User Manual

3.3.7 Backup and Restore

We can back up the configurations before resetting

TA410/810 to factory defaults, and

then restore it on this package.

Figure 3-31 Backup and Restore

Notes:

1. Only configurations, custom prompts will be backed up.

2. If you have updated the firmware version, it’s not recommended to restore using

old package.

3.3.8 Reset and Reboot

We can reset or reboot

TA410/810 directly in this page.

Figure 3-32 Reset and Reboot

·Reboot System

Warning: Rebooting the system will terminate all active calls!

·Reset to Factory Defaults

Warning: A factory reset will erase all configuration data on the system.

Please do not turn off the system until the RUN light begins blinking. Any power

interruption during this time could cause damage to the system.

33/55

«
...
31
32
33
34
35
...
»

Summary of Contents for NeoGate TA410
























































Reviews:

No comments

Related manuals for NeoGate TA410

Brand: Pathport Pages: 3

Nmea Connect Plus

Brand: Calypso Pages: 21

Brand: Farfisa Pages: 12

pathport quattro

Brand: pathway Pages: 14

Brand: Deb Pages: 4

Brand: Eaton Pages: 2

Brand: Datapulse Pages: 26

PagePro VIP-201

Brand: Valcom Pages: 4

Brand: QUPIT Pages: 16

Brand: Telecom FM Pages: 79

Brand: Sole Digital Pages: 15

Brand: Dinstar Pages: 12

SURFboard SBG6400

Brand: ARRIS/Motorola Pages: 59

Touchstone TG862

Brand: Arris Pages: 2

Touchstone TG3452

Brand: Arris Pages: 2

Brand: Alcatel-Lucent Pages: 2

Brand: ViewSonic Pages: 57

Brand: Zoom Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands