background image

Recovery Mode on Yealink IP phones

 

11

 

 

 

 

 

 

5.

 

Press          to verify the current firmware version after upgrading successfully. 

Note 

For VCS (Video Conferencing System) Series 

The section is only applicable to the VCS series including VC400, VC120, and VC110. 

The following procedures take the VC400/VC120 for reference. 

Procedures

 

1.

 

Long press the recessed 

Reset

 key (Use the tip of a pin to hold the reset key) and press          on the 

codec to trigger the recovery mode. Do not release the 

Reset

 key until the recovery mode wizard 

appears on the display device. 

Note 

2.

 

Enter the desired values in the 

IP Address

Netmask

IP Gateway

 and 

TFTP Server

 fields 

respectively. 

The IP phone must be configured in the same subnet as the TFTP server. 

 

 

 

 

 

 

 

3.

 

Press          on the remote control to complete the recovery mode.   

The video conferencing system will download and upgrade the firmware from the TFTP server. After 

upgrading, the video conferencing system will initialize successfully and get ready for use. 

4.

 

Press          on the VCP40 phone to verify the current firmware version after upgrading successfully. 

You need to press          (for SIP-T19(P) E2 IP phones), 

tap        ->

Status 

(for SIP VP-T49G IP 

phones), tap 

Settings

->

Status

 (for VP59/SIP-T58A IP phones) or tap 

Menu

->

Status

 (for 

SIP-T57W IP phones),          (for SIP-T3 IP phones) 

to

 

verify the current firmware version since 

there is no          key.

 

For VC110, you need to long press the 

Reset

 key and reconnect the power adapter to trigger the 

recovery mode. 

IP Address: 

Netmask: 

IP Gateway: 

TFTP Server: 

10.    2. 11.124 

255.255.255.    0 

10.    2. 11.254 

10.    2. 11.123 

 

….

        Update Fail       

….

 

Please reboot 

Welcome 

Summary of Contents for SIP-T19(P) E2



















Reviews: