background image

5 Installation Procedure

16

YASKAWA

SIEP C730600 88F MECHATROLINK-III Technical Manual

1.

Put the LED label (A) in the correct position on the drive front cover (B).

A - LED label

B - Drive front cover

Figure 5.9 Put the LED Label on the Drive Front Cover

2.

Shut off power to the drive, wait the appropriate amount of time for voltage to dissipate, then remove the
front cover (D).
Refer to the manual packaged with the drive for instructions on how to remove the cover.

NOTICE

Observe correct electrostatic discharge (ESD) procedures when touching the option. Failure to obey

can cause ESD damage to the option circuitry.

Note:

1. Move the keypad connector to the holder on the drive after removing the keypad and before removing the front cover.
2. Insert the keypad connector tab into the holder when installing the keypad connector to the holder.

A - Holder
B - Keypad connector tab
C - Keypad connector

D - Drive front cover
E - Keypad

Figure 5.10 Remove the Front Cover and Keypad

3.

Carefully remove the LED Status Ring board (A) and put it on the right side of the drive using the
temporary placement holes (B).
Refer to the manual packaged with the drive for information on how to remove the LED Status Ring board.

Note:

• Make sure that the LED status ring board is safe after you remove it from the bracket.
• Do not remove the LED Status Ring board cable connector. Failure to comply could cause erroneous operation and

damage the drive.

Summary of Contents for SI-ET3























































Reviews: