background image

Document Revision:  v1.0.5

of

6

10

page

18805 Adams Ct., #110   ~   Morgan Hill, CA 95037, USA   ~  +1-408.924.0808   ~   www.washlinksystems.com   ~   [email protected]

Document Title:  Tech Guide ~ Yaskawa V1000 Basic User Guide 

Common Drive Monitors

Note:  these are basic tips, refer to the technical manual for more information

U1-01

Frequency Reference Monitors the frequency 

U1-02

Output Frequency Displays the output frequency. Display units are determined by o1-03.

U1-03

 Output Current Displays the output current. 

U1-04

 Control Mode Control method set in A1-02.

U1-05

 Motor Speed Displays the motor speed feedback. Display units are determined by o1-03.

U1-06

 Output Voltage Reference Displays the output voltage. 

U1-07

 DC Bus Voltage Displays the DC bus voltage. 

U1-08

 Output Power Displays the output voltage (this value is determined internally).

U1-13

 Terminal A1 Input Level Displays analog input A1 level: 100% when input is 10 V.

U1-14

 Terminal A2 Input Level Displays analog input A1 level: 100% when input is 10 V.

U3-01

 Most Recent Fault Displays the most recent fault.

U3-02

 2nd Most Recent Fault Displays the second most recent fault. 

U3-03

 3rd Most Recent Fault Displays the third most recent fault. 

U3-04

 4th Most Recent Fault Displays the fourth most recent fault.

U3-05

 5th Most Recent Fault Displays the fifth most recent fault. 

U3-06

 6th Most Recent Fault Displays the sixth most recent fault.

U3-07

 7th Most Recent Fault Displays the seventh most recent fault. 

U3-08

8th Most Recent Fault Displays the eighth most recent fault. 

U3-09

 9th Most Recent Fault Displays the ninth most recent fault.

U3-10

 10th Most Recent Fault Displays the tenth most recent fault.

U4-01

 Accumulated Operation Time Displays the cumulative operation time of the drive.

U4-02

 Number of Run Commands Displays the number of times the run command is entered.

Summary of Contents for PROFINET V1000











Reviews: