YASKAWA DI-A3 Installation Manual Download Page 5 | Manualshive

Page: 5 / 24

YASKAWA DI-A3 Installation Manual Download Page 5

1 Preface

YASKAWA ELECTRIC

TOBP C730600 39A YASKAWA AC Drive-Option Card DI-A3 Installation Manual

5

◆

Registered Trademarks

• Company names and product names listed in this manual are the registered trademarks of

those companies.

◆

Supplemental Safety Information

Read and understand this manual before installing, operating or servicing this option unit.
The option unit must be installed according to this manual and local codes.
The following conventions are used to indicate safety messages in this manual. Failure to

heed these messages could result in serious or possibly even fatal injury or damage to the

products or to related equipment and systems.

DANGER

Indicates a hazardous situation, which, if not avoided, will result in death or serious
injury.

W ARNING

Indicates a hazardous situation, which, if not avoided, could result in death or serious
injury.

CAUTION

Indicates a hazardous situation, which, if not avoided, could result in minor or moderate
injury.

NOTICE

Indicates an equipment damage message.

«
...
3
4
5
6
7
...
»

Summary of Contents for DI-A3

























Reviews:

No comments