YASKAWA CM093 Manual Download Page 11

Yaskawa Electric America, Inc. – 

www.yaskawa.com

IG.V7.26, Page 11 of 11

Date: 05/24/2010 Rev: 10-05

V7 EtherNet/IP Option Kit

CM093

Copies of this Installation Guide along with all technical manuals in “.pdf” format
and support files may be obtained from either the CD supplied with the V7 drive
or from 

www.yaskawa.com

. Printed copies of any Yaskawa manual may be

obtained by contacting the nearest Yaskawa office. Information on MODBUS
TCP/IP may be obtained from 

www.odva.org

.

Reference documents:

V7 Technical Manual

 – TM.V7.01

V7 EtherNet/IP Technical Manual

 – TM.V7.26

Application Note – Using the Yaskawa AC Drive “EtherNet/IP” Option
with Controllogix / Compactlogix Programmable Controllers

 – AN.AFD.09

Application Note – Commissioning the Yaskawa Drive EtherNet/IP Option
with the Rockwell BOOTP/DHCP Server

 – AN.AFD.10

EtherNet/IP CONFORMANCE TESTED™ is a certification mark of ODVA.

YASKAWA ELECTRIC AMERICA, INC.

Chicago-Corporate Headquarters   
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone: (800) YASKAWA (800-927-5292) Fax: (847) 887-7310   
Internet: http://www.yaskawa.com

YASKAWA ELECTRIC CORPORATION

New Pier Takeshiba South Tower, 1-16-1, Kaigan, Minatoku, Tokyo, 105-0022, Japan
Phone: 81-3-5402-4511   Fax: 81-3-5402-4580   
Internet: http://www.yaskawa.co.jp

YASKAWA ELECTRIC EUROPE GmbH

Am Kronberger Hang 2, 65824 Schwalbach, Germany
Phone: 49-6196-569-300   Fax: 49-6196-888-301

Summary of Contents for CM093












Reviews: