background image

7

ASSEMBLY/PRE-OPERATION

CAUTION: Read complete INSTRUCTION 
MANUAL before operating this machine. 

IMPORTANT: 

THIS LAWN MOWER IS SHIPPED 

WITHOUT OIL OR GASOLINE IN THE ENGINE.

Your new lawn mower has been assembled at the factory 
with the exception of those parts left unassembled for 
shipping purposes. All parts such as nuts, washers, 
bolts, etc., necessary to complete the assembly have 
been placed in the parts bag. To ensure safe and proper 
operation of your lawn mower, all parts and hardware you 
assemble must be tightened securely. Use the correct 
tools as necessary to ensure proper tightness.

SETUP

TO REMOVE LAWN MOWER FROM CARTON
1. Remove loose parts included with mower.
2. Cut down two end corners of carton and lay end panel

EPXO «BU

3. Remove all packing materials except padding between

upper and lower handle and padding holding operator
presence control bar to upper handle.

4. Roll lawn mower out of carton and check carton

thoroughly for additional loose parts.

HOW TO SET UP YOUR LAWN MOWER

IMPORTANT:

 Unfold handle carefully to avoid pinching 

or damaging the control cables.

1. Raise handles until lower

handle section locks into
place in mowing position.

2. Insert handle bolts into

lower handle. Install and
tighten 

knobs

 to secure

the handle.

3. Remove protective

padding, raise upper
handle section into
place on lower handle.

4. Tighten 

knobs

 to

secure the handle.

5. Remove handle padding holding 

operator presence

control bar

 to upper handle (IF EQUIPPED).

NOTE:

 For some models, the lawn mower handle can 

CF BEKVTUFE GPS ZPVS NPXJOH DPNGPSU 3FGFS UP UIF ¡50

"%+645 )"/%-&¢ TFDUJPO PG UIF PQFSBUPS¤T NBOVBM

6. Loosen knob on upper

handle.

7. Slowly pull engine 

starter

handle.

8. Slip starter rope into loop

on upper handle.

NOTE: 

Make sure loop is 

facing UP.

9. Tighten 

knob.

TO ASSEMBLE THE 
GRASS CATCHER

1. Put the 

grass catcher

frame into the grass bag
with the rigid part of the
bag on the bottom. Make
sure the frame handle is
outside of the bag top.

1

2

3

4

1

7

6

8

9

Setup

model numbers  060-1662-4  |  060-1663-2  |  060-1664-0  |  060-1665-8  |  contact us: 1.866.523.5218

Summary of Contents for 060-1662-4



















Reviews: