manualshive.com logo in svg

Yardistry YM11909, Installation And Operating Instructions Manual

Share
Download
Yardistry YM11909 Installation And Operating Instructions Manual Download Page 32

 32 

[email protected]

Avery Inst 6F - Attach Roof Cap - Short

Avery Inst 6F - Attach Roof Cap - Short

Avery Inst 6F - Attach Roof Cap - Short

Avery Inst 6E - Attach Roof Cap

A:

  Slide Ridge Cap over the Ridge Clips towards the centre of the roof.  (F10.1 and F10.2)

B: 

 With the swaged end facing in slide one Ridge Cap Short at each end of the roof over the Ridge Clips.  Use 

the swaged end to help push the Ridge Cap to the centre of the roof.  Each Ridge Cap Short should be flush to 

the outside edge of the roof.  (F10.1, F10.3 and F10.4)

Components:

1  x  Ridge Cap
2  x  Ridge Cap Short

Ridge 

Cap

Ridge 

Clip

Ridge Cap 

Short

Ridge Cap 

Short

Ridge 

Cap

F10.1

F10.2

F10.3

x 2

Swaged 

End

Step 10:  Attach Ridge Caps 

Part 1

F10.4

Ridge 

Clip Short

Ridge Cap 

Short

Ridge Cap 

Short

Ridge Cap 

Short

Slide Ridge Cap Short to 

centre Ridge Cap

Note:  To help Ridge Cap 

slide on easier use a 

lubricant such as liquid soap.

Summary of Contents for YM11909









































Reviews:

No comments

Brands by name

Popular brands

Load more brands