manualshive.com logo in svg

Yardistry YM11909, Installation And Operating Instructions Manual

Share
Download
Yardistry YM11909 Installation And Operating Instructions Manual Download Page 29

 29 

[email protected]

A:

  With four assemblers lift one Roof Panel Frame up and over Post and Beam Frame Assembly so the notches 

in (831) Rafters rest on Side Beam Assembly and (837) Rafter Tops are flush to the outside of each (846) Gable 

Upright Assembly.  

One assembler must remain on a ladder to hold Roof Panel Frame in place until secured.

  

(F9.1, F9.2 and F9.3)

B:

  Lift the second Roof Panel Frame so the notches in (831) Rafters rest on Side Beam Assembly and (837) 

Rafter Tops are flush to the outside of each (846) Gable Upright Assembly and is tight to the first Roof Panel 

Frame.  (F9.1, F9.2 and F9.3)

Step 9:  Attach Roof Panels to Frame 

Part 1 

F9.1

Roof Panel 

Frame

F9.2

Notch rests on Side 

Beam Assembly 

One assembler to support Roof 

Panel Frames at all times until 

secure

Side Beam 

Assembly

Side Beam 

Assembly

x 3

F9.3

Flush

Flush and 

Tight

Roof Panel 

Frame

(846) Gable 

Upright 

Assembly

(837) Rafter Top 

(846) Gable 

Upright 

Assembly

(837) Rafter 

Top

(831) 

Rafter

(831) 

Rafter

(831) 

Rafter

Summary of Contents for YM11909









































Reviews:

No comments

Brands by name

Popular brands

Load more brands