manualshive.com logo in svg

Yardistry 12' x 12' MERIDIAN GAZEBO YM11769, Installation And Operating Instructions Manual, Page: 19 / 44

Share
Download
Yardistry 12' x 12' MERIDIAN GAZEBO YM11769 Installation And Operating Instructions Manual Download Page 19

 19 

[email protected]

A:

  On each side of one (340) Rafter place one (333) Rafter Corner Left and one (334) Rafter Corner Right so 

the tops and edges are flush then attach with two #8 x 2-1/4” Wood Screws per side.  (Fig. 7.1 and 7.2)

B:

  Place Fascia Beam Assembly from Step 6 on the bottom of (333) Rafter Corner Left, (334) Rafter Corner 

Right and (340) Rafter so the sides are flush then attach with two #8 x 2-1/4” Wood Screws at each end and two 

in the middle.  (fig. 7.1, 7.3 and 7.4)

C:

  Repeat Steps A and B three more times to make four Roof Rafter Assemblies.

7

7

7

7

Hardware

Wood Parts

#8 x 2-1/4” Wood Screws 

(x 6 per Fascia Beam 

Assembly)

(340) 

Rafter

Top View

Fascia Beam 

Assembly

Step 7: Roof Rafter Assembly 

Part 1

Fig. 7.1

40 x #8 x 2-1/4” Wood Screw

4  x  (340) Rafter
4  x  (333) Rafter Corner Left
4  x  (334) Rafter Corner Right

Fig. 7.3

Fig. 7.4

Note notches 

facing up

Flush

Fascia Beam 

Assembly

Fascia Beam 

Assembly

Flush

(340) 

Rafter

(340) 

Rafter

#8 x 2-1/4” 

Wood Screws

#8 x 2-1/4” 

Wood Screws

Flush

Fig. 7.2

(333) Rafter 

Corner Left

(333) Rafter 

Corner Left

(333) Rafter 

Corner Left

(334) Rafter 

Corner Right

(334) Rafter 

Corner Right

Front View

Front View

Note angle 

side up

Summary of Contents for 12' x 12' MERIDIAN GAZEBO YM11769













































Reviews:

No comments