Yardistry 12' x 12' MERIDIAN GAZEBO YM11769 Installation And Operating Instructions Manual Download Page 13 | Manualshive

Page: 13 / 44

Yardistry 12' x 12' MERIDIAN GAZEBO YM11769 Installation And Operating Instructions Manual Download Page 13

13

[email protected]

Step 3: Beam Assembly

Part 1

Hardware

Wood Parts

A:

Connect one (718) Beam End Left and one (719) Beam End Right using two 5/16 x 1-1/2” Hex Bolts (with

5/16” lock washer, 1/4 - 5/16” large washer and 5/16” t-nut) as shown in fig. 3.1 and 3.2.

B:

Connect one (720) Beam End Short to each end of one (717) Beam using two 5/16 x 1-1/2” Hex Bolts (with

5/16” lock washer, 1/4 - 5/16” large washer and 5/16” t-nut) per end as shown in fig. 3.1 and 3.2.

C:

Repeat Steps A and B three more times to make four Beam Short Assemblies and four Beam End

Assemblies.

4 x (718) Beam End Left
4 x (719) Beam End Right
8 x (720) Beam End Short
4 x (717) Beam

24 x 5/16 x 1-1/2” Hex Bolt

(5/16” lock washer, 1/4-5/16” large washer, 5/16” t-nut)

(718) Beam

End Left

Fig. 3.1

Fig. 3.2

1/4 -5/16”

Large Washer

5/16 x 1-1/2”

Hex Bolt

5/16”

T-nut

Tight

(719) Beam

End Right

(717) Beam

(720) Beam

End Short

(720) Beam

End Short

5/16” Lock

Washer

Make sure bolt heads

are on the outside of

each Beam Assembly

«
...
11
12
13
14
15
...
»

Summary of Contents for 12' x 12' MERIDIAN GAZEBO YM11769













































Reviews:

No comments