Yardistry 12' x 12' MERIDIAN GAZEBO YM11769 Installation And Operating Instructions Manual Download | Manualshive

Page: 11 / 44

background image

11

[email protected]

PRODUCT NUMBER:

YM11769

CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 3)

STOP

STOP

STOP

STOP

1-888-509-4382

[email protected]

C.

Read the assembly manual completely, paying special attention to ANSI

warnings; notes; and safety/maintenance information on pages 1 - 4.

•

Follow the instructions in order.

•

This structure is designed to be assembled and installed ideally by four

people, DO NOT attempt to install alone.

• Consider the slope of elevation where you plan to install the structure. Also, check

for gas, telephone, other utilities or sprinkler line locations prior to excavating any

holes.

D.

Before you discard your cartons fill out the form below.

• The carton I.D. stamp is located on the end of each carton.

• Please retain this information for future reference. You will need this information if

you contact the Consumer Relations Department.

• Each step indicates which bolts and/or screws you will need for assembly, as

well as any flat washers, lock washers, t-nuts or lock nuts.

A.

This is the time for you to inventory all your hardware, wood and accessories,

referencing the parts identification sheets. This will assist you with your

assembly.

Step 1: Inventory Parts - Read This Before Starting Assembly

B.

If there are any missing or damaged pieces or you need assistance with

assembly please contact the consumer relations department directly. Call us

before going back to the store.

«
...
9
10
11
12
13
...
»

Summary of Contents for 12' x 12' MERIDIAN GAZEBO YM11769













































Reviews:

No comments

Related manuals for 12' x 12' MERIDIAN GAZEBO YM11769

Brand: Safco Pages: 3

FOXFIELD PHEL5104BLK

Brand: Park Harbor Pages: 2

Brand: Landmann Pages: 6

Brand: Canada Comfy Chair Pages: 2

Tenera Auto-Lift

Brand: Lafayette Pages: 3

Brand: IBEX Pages: 6

FOLDING PROCESSING TABLE

Brand: Bass Pro Shops Pages: 2

TRENDY Woodie 66094

Brand: deVRIES Pages: 8

Brand: MARCKERIC Pages: 18

Brand: IKEA Pages: 12

Brand: Symphony Pages: 12

Brand: Yardistry Pages: 60

Brand: Bestar Pages: 20

Brand: Twin-Star International Pages: 28

Brand: Living Pages: 17

Brand: Walker Edison Pages: 15

Brand: Home Accents Holiday Pages: 2

Brand: Homebase Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands