background image

18

19

GB

GB

Problem

Possible cause

Corrective action

Mower runs in circles

Power cable runs parallel/close to 
wire

Reposition of boundary wire

Front wheel is stuck

Clean front wheel area

Signal interfere with robot in 
neighborhood

Change to alternative boundary 
signal (S1/S2)

Driving motor failure

Please call after sales service

Connection issue or broken/cut 
boundary wire

Repair/check connections on 
charge base and boundary wire 
being broken/cut

Function ON/OFF by key combination

Function

Operation

Pin code reset

Press and hold         button, then power on

Time calibration

Press and hold         button, then power on

Boundary mowing *

Press and hold         button, then power on

Auto multi-zone *

Press and hold         button, then power on

Rain sensor on/off

Press and hold         button, then power on

Boundary mowing * 

Function description: the mower will mow along the entire boundary wire with maximum 2 days 
interval.

Auto multi-zone * 

The mower will measure the complete boundary value and divide it into several points equally, 
everytime after charging, the mower will go to each point sequentially and then start cutting from 
this point.

Charging trouble shooting

Problem

Possible cause

Corrective action

No light on charge base

Incorrect wire connection

Check wire connections "F and B"

AC Power has not been switched 

ON

Switch on AC power 

S1 or S2 indicator flashes 
separately

Boundary wire broken, no signal

Repair broken cable with provided 
connectors

Robot not charging 

Machine not correctly docked in 
charge base

Check machine is fully docked in 
charge base
Check charge base is on flat 
surface

Charger pins corroded

Clean the charger pins

Mowing trouble shooting

Problem

Possible cause

Corrective action

No Power to machine

ON/OFF key has not been 
activated

Switch ON the machine and try 
again

Robotic Mower has low charge

Place machine in the docking 
station

Machine fails to START

Time setting not activated

Select time schedule and then try 
again

Grass build up under deck

Clean under deck with brush 

Battery power low

Place machine in docking station

Grass too long 

Mow the lawn to 60mm

Cutting height is too low 

Mow the lawn to 60mm and raise 
cutting height

Battery temperature too cold /hot

Working condition is between 5 
and 45 

o

C

Boundary wire broken

Repair broken boundary wire

Mower outside the 
boundary wire

Boundary wire is on a slope

Modify boundary wire and leave 
bigger distance on slope

Parts of the lawn are 
uncut

Mower needs more cutting time

Increase scheduled cutting time to 
8 hrs

Grass too long 

Mow the lawn to 60 mm

Mower gets stuck in Lawn 
area

Obstacles on lawn

Remove obstacles from the lawn

Boundary wire not correct laid

Modify boundary wire to zone out 
obstacles

Wire in front of docking station 
incorrect installed

1.5 m of straight cable to front of 
docking station needed

Excessive vibration/noisy

Blade loose

Tighten screw bolt

Blades damaged jammed

Replace damaged blades

Grass maybe to high

Increase cutting height, reduce 
later step by step or mow the lawn 
with ordinary lawnmower first

Cutting motor failure

Please call the after sales service

Summary of Contents for Classic 500













Reviews: