manualshive.com logo in svg

Yamato MK161, Manual, Page: 17 / 22

Share
Download
Yamato MK161 Manual Download Page 17

 

15

 

8. When a trouble occurs   

 

Countermeasures for malfunctions 

 

Symptom Causes 

Countermeasures 

Even if the switch is turned on 

・

 

No display appears 

・

 

Shaking does not start 

①

 

Imperfect contact of a circuit 

②

 

Defect of the power switch 

③

 

Fuse has blown 

④

 

Defective substrate or imperfect 
contact 

①

 

Replace or repair 

②

 

Replace 

③

 

Replace 

④

 

Replace or repair 

Although shaking is made 

・

It is not smoothly. 

・

Excessive noises or 

vibrations 

①

  Roller is worn 

②

 Belt is loosened 

③

  Belt is worn or damaged 

④

  Anti-vibration rubber is defective 

⑤

  Floor is not flat 

①

 

Replace 

②

 

Adjust belt tension 

③

 

Replace 

④

 

Replace 

⑤

 

Move to a different 
site 

Speed is uncontrollable 

①

 

Speed controller is defective 

②

 

Motor is defective 

①

 

Replace 

②

 

Replace 

 

                                     

If a malfunction is suspected 

 

In such cases 

Symptom Check 

The unit will not operate 
even though power is 
turned on. 

●

If the power cord is connected to an outlet securely. 

●

If a power failure has occurred. 

●

If the fuse has blown. 

Shaking speed fluctuates 
during operation. 

●

If the amount of specimen is too much. 

●

If specimen is concentrated to one side. 

●

If source voltage is too low. 

Shaking stops. 

●

If the shaking table is not overloaded. 

●

If a foreign object is pinched in the shaking table.

 

 

◆

 

If the symptom does not fall on any of the categories above, immediately turn the power 
switch off, turn the source power off and contact your dealer, one of our sales office, or our 
general customer service center.

 

Summary of Contents for MK161























Reviews:

No comments