manualshive.com logo in svg

Yamato MK161, Manual, Page: 11 / 22

Share
Download
Yamato MK161 Manual Download Page 11

 

9

 

4. Operating Procedures

Performing continuous shaking operation

 
This section explains how to perform continuous shaking without using 
the timer function. 

1.  Selecting a shaking system 

Set the shaking system selector volume to the system you want. 

（

See P.11.

）

 

2. Setting specimen 

Set specimen in the rack(s) specified for optional accessories.

（

See 

P.12.

）

 

3.  Turning power on (Turning the power switch ON) 

Turn the power switch ON. 

4.  Setting a shaking speed 

Set to a shaking speed you want by turning the speed adjusting 
volume clockwise. 

Move the switch on the shaking speed adjusting panel to the 
RUN/STOP side.

 

Set the timer panel switch to [CONT.] side when you do not use 
the timer.

 

 

 

 

 

 

 

5. Starting operation 

Setting the switch on the SHAKE panel to “RUN/STOP” side will 
start shaking. Initial shaking speed may not be obtained depending 
on the load status. Make fine adjustment with the shaking speed 
adjusting volume again during operation to set a number of 
shaking.

 

 
How to perform 
shaking-only 
operation 

 

 

 

 

 

MK16１

 

 

 

 

 

min.

TIME

POWER

RUN/STOP

TIMER

CONT.

min.

max

SHAKE

r.p.m.

min.

max

PAUSE

ON

OFF

 

6. Stopping operation 

Set the switch on the shaking speed adjusting panel to the 
[RUN/STOP] side. 

7.  Pausing shaking operation

 

Set the switch on the shaking speed adjusting panel to the 
[PAUSE] side. Shaking will pause. Setting this switch to the 
[RUN/STOP] side again to resume shaking.

 

About time setting 

Timer setting time range is from 0 to 99.9 min. The minimum unit of 
time for setting is 0.1 min (6 seconds

）

. 

About setting of a 
shaking speed

 

The maximum shaking speed is 200r.p.m

（

times/min

）

. 

Avoid setting to a speed higher than this, which causes severe 
vibration of the unit and poses a danger. 

When there is a difference between the set shaking speed and the 
indicated speed, make fine adjustment using the speed adjusting 
volume during shaking. 

About shaking stroke

 

The shaking stroke for this unit is fixed at 30mm.

 

 

②

  Set this to the [CONT] side when you do not use the timer. 

③

  Set to a shaking speed you want with the volume. 

①

  Turn the power switch ON. 

④

  Move the switch upward to RUN/STOP. 

Shaking 
system 
selector 
volume 

Summary of Contents for MK161























Reviews:

No comments