manualshive.com logo in svg

YAMARIN 68 Cabin, Owner'S Manual, Page: 19 / 39

Share
Download
YAMARIN 68 Cabin Owner'S Manual Download Page 19

YAMARIN 68 Cabin 

 

 

19 (39) 

 

 

5.8

 

Main switches and fuses 

Main switches operation: 
 
 

- Switch clockwise  

 

-> battery connected 

 

- Switch counter clockwise  

-> battery disconnected 

 

START  SWITCH

SE RVICE  S WITCH

DIR. SUPPLY  SWITCH

TRIM

CABIN L.

HEATER

PLOTTER

BILGE P.

MEM.

WIPERS

NAV L.

STOWE

FRID GE

PENTRY P.

RADIO

20A

20A

20A

15A

10A

10A

10A

10A

15A

15A

25A

10A

FUSE 1

FUSE 2

FUSE 3

FUSE 4

FUSE 5

FUSE 6

FUSE 7

FUSE 8

FUSE 9

FUSE 10 FUSE 11

FUSE 12

 

 

 

 
Always keep both start and service switches connected when using the boat or any device in 
the boat.  
 

WARNING!

  Do not keep service battery switch off and start battery switch con 

ignition lock switched on as this may damage the electrical system in the boat! 
 
Following fuses are connected to the direct supply switch: Fridge, stove, memory for radio 
and Yamaha-gauges, bilge pump and heater. Please note that the automatic bilge pump will 

Summary of Contents for 68 Cabin








































Reviews:

No comments