Yamaha Z200 Owner'S Manual Download Page 58

Page: 58 / 98

Operation

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28185

Procedure for power trim and tilt / power
tilt models

Place the remote control lever / gear
shift lever in neutral.

ZMU01936

ZMU04603

ZMU03999

ZMU04588

Summary of Contents for Z200



































































































Search results

Summary of Contents for Z200

Reviews:

Brands by name

Popular brands

Yamaha Z200, Owner'S Manual

Search results

Summary of Contents for Z200

Reviews:

Brands by name

Popular brands