background image

 

Basic components

 

34

 

If the warning system has activated, stop the
engine and check the cooling water inlet for
clogging.

NOTE:

 

Dual engine drive users:
Should the overheat warning system of one
engine activate, the engine will slow down
and the buzzer will sound. This will cause the
other engine to slow down and the buzzer to
sound. To switch off the warning activation

on the engine not affected by overheating,
turn off the main switch of the engine over-

 

heating.

 

EMU26846

 

Oil level warning and oil filter 
clogging warning

 

Oil injection models

 

This engine has an oil level warning system.
If the oil level falls below the lower limit, the
warning system will activate.

 

Activation of warning device

 

 

Engine speed will automatically decrease
to about 2000 r/min.

 

 

The oil level warning indicator will light or
blink.

 

 

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

OFF

START

ON

OFF

START

ON

ZMU04584

ZMU02630

ZMU03942

ZMU04586

Summary of Contents for Z200



































































































Reviews: