Yamaha Z200 Owner'S Manual Download

Page: 26 / 98

Basic components

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 58.

EMU31702

Water separator

This engine has a combination fuel filter/wa-
ter separator and associated warning sys-
tem. If water separated from the fuel
exceeds a specific volume, the warning de-
vice will activate.

Activation of warning device

●

The water separator warning indicator will
blink.

●

The buzzer will sound intermittently only
when the gear shift is in neutral.

●

If the warning system has activated, stop
the engine and consult a Yamaha dealer
immediately.

EMU26470

Tachometer

This gauge shows the engine speed and has
the following functions.

EMU26491

Digital tachometer

The tachometer shows the engine speed
and has the following functions.

NOTE:

All segments of the display will light momen-

1. Air intake grille
2. Top cowling lock lever(s)

1. Flushing device

ZMU04437

ZMU04011

1. Tachometer
2. Oil level indicator

ZMU05499

ZMU04577

Summary of Contents for Z200



































































































Search results

Summary of Contents for Z200

Reviews:

Related manuals for Z200

Brands by name

Popular brands

Yamaha Z200, Owner'S Manual

Search results

Summary of Contents for Z200

Reviews:

Related manuals for Z200

Brands by name

Popular brands