Yamaha YZF-R6T Owner'S Manual Download Page 69

Page: 69 / 111

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

This motorcycle is equipped with cast
wheels and tubeless tires with valves.

WARNING

EWA10480

●

The front and rear tires should
be of the same make and de-
sign, otherwise the handling
characteristics of the motor-
cycle cannot be guaranteed.

●

After extensive tests, only the
tires listed below have been ap-
proved for this model by
Yamaha Motor Co., Ltd.

●

Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.

●

Use only the tire valves and
valve cores listed below to
avoid tire deflation during a
high-speed ride.

WARNING

EWA10600

This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-

speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

Front tire:

Size:

120/70 ZR17M/C (58W)

Manufacturer/model:

DUNLOP/D218F M

Rear tire:

Size:

180/55 ZR17M/C (73W)

Manufacturer/model:

DUNLOP/D218 M

FRONT and REAR:

Tire air valve:

TR412

Valve core:

#9000A (original)

U5SL12E0.book Page 23 Monday, August 9, 2004 10:51 AM

Summary of Contents for YZF-R6T
















































































































Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands

Yamaha YZF-R6T, Owner'S Manual

Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands