Yamaha YZF-R6T Owner'S Manual Download Page 109

Page: 109 / 111

INDEX

Accessories and replacement parts ..... 6-24
Air filter element, checking ................... 6-18
Air intake duct ....................................... 6-20

Battery .................................................. 6-34
Brake and clutch levers,

checking and lubricating..................... 6-31

Brake and shift pedals,

checking and lubricating..................... 6-31

Brake fluid, changing ............................ 6-28
Brake fluid level, checking .................... 6-27
Brake lever ........................................... 3-11
Brake pedal .......................................... 3-12

Cables, checking and lubricating .......... 6-30
Canister (for California only)................. 6-11
Care ........................................................ 7-1
Catalytic converter................................ 3-14
Clutch lever........................................... 3-10
Clutch lever free play, adjusting ........... 6-25
Coolant ................................................. 6-14
Coolant temperature warning light.......... 3-3
Cowlings and panels,

removing and installing......................... 6-8

Dimmer switch ...................................... 3-10
Drive chain, lubricating ......................... 6-29
Drive chain slack .................................. 6-28

Engine break-in ...................................... 5-3
Engine oil and oil filter cartridge ........... 6-11
Engine stop switch................................ 3-10
Engine trouble warning light ................... 3-5

Front and rear brake pads, checking ....6-26
Front fork, adjusting ..............................3-16
Front fork, checking...............................6-33
Fuel .......................................................3-13
Fuel level warning light............................3-3
Fuel tank cap.........................................3-12
Fuses, replacing ....................................6-35

Handlebar switches .................................3-9
Headlight bulb, replacing.......................6-36
Helmet holders ......................................3-15
High beam indicator light.........................3-2
Horn switch ...........................................3-10

Identification numbers .............................9-1
Ignition circuit cut-off system .................3-20
Indicator and warning lights ....................3-2

Key identification number........................9-1

Labels, location of ...................................1-5
License plate light bulb, replacing .........6-38
Luggage strap holders ..........................3-19

Main switch/steering lock ........................3-1
Maintenance and lubrication, periodic.....6-4
Maintenance, emission control system ...6-3
Maintenance, periodic .............................6-1
Maintenance record ................................9-5
Model label ..............................................9-2
Multi-function display...............................3-6

Neutral indicator light ..............................3-2

Noise regulation ...................................... 9-4

Oil level warning light .............................. 3-2

Parking.................................................... 5-4
Part locations .......................................... 2-1
Pre-operation check list .......................... 4-2

Rear brake light switch, adjusting ......... 6-26

Tachometer............................................. 3-5
Tail/brake light ...................................... 6-38
Throttle cable free play, checking ......... 6-20
Throttle grip and cable,

checking and lubricating ..................... 6-30

U5SL12E0.book Page 1 Monday, August 9, 2004 10:51 AM

Summary of Contents for YZF-R6T
















































































































Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands

Yamaha YZF-R6T, Owner'S Manual

Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands