Yamaha YZF-R6T Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 111

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-2

3

EAU11002

Indicator and warning lights

EAU11030

Turn signal indicator lights “

” and

“

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11250

Oil level warning light “

”

This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.

NOTE:

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If the oil lev-
el detection circuit is defective, the
following cycle will be repeated un-
til the malfunction is corrected: The
oil level warning light will flash ten
times, then go off for 2.5 seconds.
If this occurs, have a Yamaha
dealer check the vehicle.

1. Right turn signal indicator light “

”

2. Fuel level warning light “

”

3. Oil level warning light “

”

4. Neutral indicator light “

”

5. Engine trouble warning light “

”

6. High beam indicator light “

”

7. Left turn signal indicator light “

”

1. Shift timing indicator light
2. Coolant temperature warning light “

”

3. Coolant temperature display

U5SL12E0.book Page 2 Monday, August 9, 2004 10:51 AM

«
...
18
19
20
21
22
...
»

Summary of Contents for YZF-R6T
















































































































Reviews:

No comments

Related manuals for YZF-R6T

Brand: Cannondale Pages: 102

Brand: KAYO MOTOR Pages: 74

Brand: KAYO MOTO Pages: 5

Brand: Honda Pages: 201

Brand: VIKING BAGS Pages: 2

Trekker Dolomiti

Brand: GIVI Pages: 24

Brand: Crivit Pages: 50

Easyrack 6612533 01 01

Brand: hepco & becker Pages: 5

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 580

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 509

Brand: Yamaha Pages: 508

Brand: Yamaha Pages: 510

Brand: Yamaha Pages: 578

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands