Yamaha YZF-R6T Owner'S Manual Download Page 87

Page: 87 / 111

PERIODIC MAINTENANCE AND MINOR REPAIR

6-41

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders and

reflectors by installing the bolts
and nuts.

6. Secure the wheel axle by installing

the axle bolt, and then tightening
the axle bolt to the specified
torque.

NOTE:

While tightening the axle bolt, hold the
wheel axle with a 19-mm hexagon
wrench to keep it from turning.

7. Tighten wheel axle pinch bolt B,

and then tighten pinch bolt A to the
specified torque.

8. Retighten pinch bolt B to the spec-

ified torque.

9. Tap the outer side of the right fork

leg with a rubber mallet to align it
with the end of the wheel axle.

10. Tighten wheel axle pinch bolt D,

and then tighten pinch bolt C to the
specified torque.

11. Retighten pinch bolt D to the spec-

ified torque.

12. While applying the front brake,

push down hard on the handlebar
several times to check for proper
fork operation.

Tightening torque:

Brake caliper bolt:

35 Nm (3.5 m·kgf, 25 ft·lbf)

Tightening torque:

Axle bolt:

91 Nm (9.1 m·kgf, 66 ft·lbf)

Tightening torque:

Wheel axle pinch bolt:

18 Nm (1.8 m·kgf, 13 ft·lbf)

Tightening torque:

Wheel axle pinch bolt:

18 Nm (1.8 m·kgf, 13 ft·lbf)

1. Front wheel axle pinch bolt A
2. Front wheel axle pinch bolt B

3. Front wheel axle pinch bolt C

4. Front wheel axle pinch bolt D

U5SL12E0.book Page 41 Monday, August 9, 2004 10:51 AM

Summary of Contents for YZF-R6T
















































































































Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands

Yamaha YZF-R6T, Owner'S Manual

Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands