manualshive.com logo in svg

Yamaha YZ 2017 Series, Owner'S Service Manual


Share
Download
background image

CHAIN DRIVE

4-68

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• O-rings “1”

Damage 

 Replace the drive chain.

• Drive chain rollers “2”

Damage/wear 

 Replace the drive chain.

• Drive chain side plates “3”

Damage/wear 

 Replace the drive chain.

5. Lubricate:

• Drive chain

EASB29B195

CHECKING THE DRIVE SPROCKET

1. Check:

• Drive sprocket

More than 1/4 tooth wear “a” 

 Replace the 

drive sprocket and the rear wheel sprocket 
as a set.
Bent tooth 

 Replace the drive sprocket 

and the rear wheel sprocket as a set.

EASB29B196

CHECKING THE REAR WHEEL SPROCKET

Refer to “CHECKING AND REPLACING THE 
REAR WHEEL SPROCKET” on page 4-8.

EASB29B197

INSTALLING THE DRIVE CHAIN

1. Install:

• Drive chain

ECA

NOTICE

Be sure to put on safety goggles when 
working.

TIP

Install the drive chain joint with the drive chain 
cut & rivet tool. (Use goods on the market)

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. When press fitting the connecting plate “1”, 

make sure the space “a” between the end of 
the connecting pin “2” and the connecting 
plate is 1.2–1.4 mm (0.05–0.06 in).

Recommended lubricant

Chain lubricant suitable for O-

ring chains

b. Correct

1. Drive chain roller

2. Drive sprocket

Summary of Contents for YZ 2017 Series



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZ 2017 Series

Fantic Motor 125 Series Owner'S Manual preview
125 Series
Brand: Fantic Motor Pages: 130
hepco & becker 410999 00 01 Quick Start Manual preview
410999 00 01
Brand: hepco & becker Pages: 2
SCORPION Exo-R410 Technical Manual preview
Exo-R410
Brand: SCORPION Pages: 12
PZRacing GearTronic ZERO GT3100-K1 User Manual preview
GearTronic ZERO GT3100-K1
Brand: PZRacing Pages: 2
RDMOTO CF124 Quick Start Manual preview
CF124
Brand: RDMOTO Pages: 2
APRILIA SCARABEO 100 4T - 06-2001 PART6 Manual preview
SCARABEO 100 4T - 06-2001 PART6
Brand: APRILIA Pages: 6
Sinnis motorcycles TERRAIN 125 Owner'S Manual preview
TERRAIN 125
Brand: Sinnis motorcycles Pages: 68
Ericsson ORION Installation Manual preview
ORION
Brand: Ericsson Pages: 44
Eastwood L6700 Instructions Manual preview
L6700
Brand: Eastwood Pages: 8
Wunderlich 35520-002 Manual preview
35520-002
Brand: Wunderlich Pages: 2
Engelbert Strauss 75.76.501 Operating Instructions Manual preview
75.76.501
Brand: Engelbert Strauss Pages: 32
RIEJU Enduro Owner'S Manual preview
Enduro
Brand: RIEJU Pages: 49
Benelli 2009 TREK1130 Workshop Manual preview
2009 TREK1130
Brand: Benelli Pages: 582
Yadea M6L Service Menu preview
M6L
Brand: Yadea Pages: 66
COLORADO DR 2336 Operator'S Handbook Manual preview
DR 2336
Brand: COLORADO Pages: 21
Rewaco RF1 Operating Instructions And Service Manual preview
RF1
Brand: Rewaco Pages: 42
HealTech Electronics FI Cleaner Tool User Manual preview
FI Cleaner Tool
Brand: HealTech Electronics Pages: 2
Ossa EXPLORER 2014 User Manual preview
EXPLORER 2014
Brand: Ossa Pages: 70

Brands by name

Popular brands

Load more brands