Yamaha YFM4FAR Service Manual Download Page 368

Page: 368 / 397

9 - 35

–

ELEC

SIGNAL SYSTEM

CHECKING THE SIGNAL SYSTEM

1.If the brake light fails to come on:

CONTINUITY

1.Bulb and bulb socket

●

Check the bulb and bulb socket for
continuity.

NO CONTINUITY

Replace the bulb and/or bulb socket.

CONTINUITY

2.Brake light switches

Refer to “CHECKING THE SWITCHES”.

NO CONTINUITY

Replace the brake light switch.

3.Voltage

●

Connect the pocket tester (DC 20 V) to the
bulb socket connector.

Tester (+) lead

→

Yellow terminal

Tester (–) lead

→

Black terminal

MEETS
SPECIFICATION

●

Turn the main switch to “ON”.

●

Pull in the brake lever or push down on the
brake pedal.

●

Check the voltage (12 V) of the “Yellow”
lead on the bulb socket connector.

This circuit is not faulty.

OUT OF SPECIFICATION

The wiring circuit from the main switch to the
bulb socket connector is faulty, repair it.

Summary of Contents for YFM4FAR














































































































































































































































































































































































































Search results

Summary of Contents for YFM4FAR

Reviews:

Related manuals for YFM4FAR

Brands by name

Popular brands

Yamaha YFM4FAR, Service Manual

Search results

Summary of Contents for YFM4FAR

Reviews:

Related manuals for YFM4FAR

Brands by name

Popular brands